57441D0WW General Electric Washer - Instructions

Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

at the bottom of the tub their is a mettal peace witch holds the tub to the transmision witch is made of zink(aka junk metal or zink+tin)witch broke stoping tub from sping the clotes dry so atfer odering the new part and nut..
and finding out that it is a LEFTHAND nut made of alumanum
taking a small drill bit 1/8" and drilling the nut to weakin it making it brake able then cleaning the treds up
the new part fit right in the tufest part was hold the trans still to get the nut on tightenuf to hold the tub

Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Unplugged the washer and unscrewed the hot and cold filler hoses from the back of the machine. Removed the 6 screws holding the top together. Unscrewed the 2 water valve mounting screws. Pulled off the electrical wires from the leads. Unclipped the water feed hose clip. Reattached everything to the new water valve in reverse order. Put the screws holding the top panel in place back in.

For good measure, I also replaced the drain hose since I had noticed a little leakage there. Two screws and a little twisting and pushing was all that took.

Then I hooked everything back up and it worked like a charm. Finally, I went out to dinner with my wife on the money I saved!

On Friday the 13th, after spilling my coffee all over the table, I put the tablecloth in to wash. When I pulled the tablecloth out of the washer & put it into the dryer, I must have been angry at myself because I wrenched the dryer "Start" knob too hard & broke the knob off! I spent a few minutes looking for the part, and found that PartSelect had exactly what I needed at a very reasonable price. Once ordered, I received order confirmation, and, amazingly, the part arrived at my home in less than 24 hours after I broke the knob! Thanks, PartSelect!

Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.

Removed by pulling out. Removed coupling air bell with socket and replaced. Wery well. Thnak you.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.