WPRE8320H1WT General Electric Washer - Instructions

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

watched the video, and it was simple!

Worse machine ever made. Installed all parts per videos .they helped a lot. Inner tub went on crooked and first wash ruined inner/outer tubs top piece. Took to dump.

The first attempt to fix the problem did not turn out so well. I replaced the tub bearing, split ring, tub bearing washer and the hub washer. After reassembly and testing, the loud airplane noise was still present during the spin cycle
Then I ordered and replaced the mode shifter shaft assembly and, since I was going to disassemble again, also ordered a new 6-rib belt. Once reassembled and tested, it was quieter than when it was when brand new, according to my wife.
Parts came in very quickly and the tutorials/youtubes were spot on.

I removed the front cover and the top cover. Then I unplugged all the,wires and removed the hangers. Then removed tub and drum together out the front. After beating on the tub nut for 2 hours and drenching it in liquid wrench I realized that the,tub nut was not going to release. Yes I was turning it clockwise. I bring out my chisel and hammer. After removing the,center shaft I chisel the,tube inward till I could get to the nut. Then I chisel the,tub nut into 3 pieces. It then appeared why it wasn't coming loose,earlier the powders,had gotten below the nut and had it cemenred on. So those youtube videos,are helpful to an extent.

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

Top panel was exactly what I needed and fit perfectly. To replace the top panel I first unplugged power. Removed control panel on top of machine. Removed front panel by placing a putty knife under front corners and pushing down on front panel. Removed two screws holding top panel to frame. Removed lid switch from top panel then removed lid from top panel. Lift up front of top panel and slide out of cabinet. Replaced new top panel in reverse order. The only thing I overlooked when ordering top panel was the plastic bumpers and rubber guides for the lid. Had to remove old parts from old top panel and use them. Overall job took about 45 minutes.

Took complete tub assembly out of washer and inspected it. Did not find an obvious cause of leak but all 8 screws on inner tub hub were loose. As both tub nut and split ring were corroded, replaced them and the outer tub seal. Did a lot of cleaning!! As I was putting the trans assy back on the outer tub, I noticed a crack around the drain spout. At 1st, it looked like it belonged there but a closer look proved it didn't. I ordered a new outer tub (which came in 2 days) and I put the whole thing back together. Reassembly was far easier than disassembly was and I learned a whole lot about washers. YouTube is a great source of information.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

My wife washed a washable mop head and somehow it managed to break one of the fins off the agitator. I ordered a new agitator, fabric softener dispenser, agitator coupling, and bolt. I figured since I had to replace the agitator I would replace everything. This was super simple and easy. I watched a few videos on getting the agitator off, some people said you may need to run some rope under it to get it off. Luckily mine popped right off. I grabbed both sides and gave it a good solid jerk straight up and it came right off. I used a 3/8 drive socket wrench and a 7/16 socket to remove the bolt from the agitator coupling. I installed the new coupling with a new bolt, lined up the agitator and snapped it right on. Popped in the new fabric softener dispenser and that was it. I may have spent a total of 10 minutes counting unpacking the new parts and carting the old ones out to the trash can replacing this. If you can operate a socket wrench or a new smart phone this is really a piece of cake.

Followed instructions from video for shaft and mode shifter assembly and tub bearing, all went as in video except extremely difficult to remove tub nut. Could not get nut to loosen and when it did finally move it was spinning the whole shaft, had to have the shaft held with a pipe wrench from underneath (2nd person). The tub seal was another issue, removal was easy just as in the video but because water had gotten inside the seal it caused the internal metal of the seal to corrode and rust which deformed the old seal and the plastic of the tub where the seal sits. There was no way the new seal would go in and be tight enough to seal so I put a hose clamp around it, heated the plastic with a heat gun just enough to be able to tighten the clamp several times, let it cool and removed the clamp. It held its shape and the new seal went in snug so I proceeded with the reassembly. Test ran the washer and checked for leaks, no leaks. It has been a week now and approximately 10 loads of clothes cleaned, all is good.