GTW180SCJ0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from BLUFF DALE, TX
- Parts Used:
- WH13X22720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water would not shut off
Removed screws off back of washer where controls are located. Unplugged the wires to the part removed the screws holding it in place. Put in new part, put in screws, plugged the wires into part replaced screws onto back of washer and plugged washer back in and works great.
This is the 2nd one we have had to replace, purchased each one from part select. Seems this part only last 2-3 years.
This is the 2nd one we have had to replace, purchased each one from part select. Seems this part only last 2-3 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LEXINGTON, OH
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harwinton, CT
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Kiln, MS
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stanley from Pownal, VT
- Parts Used:
- WH43X10034
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replaceed agitator
Old agitator was stuck on and i could not pull it of.I used two claw hammers and put the claw under the agitator and broke it free.Worked perfect" Took five minutes "
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Port Hueneme, CA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Spring city, PA
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bad lid switch
Watched the how to video, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from State College, PA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from FLORENCE, KY
- Parts Used:
- WH41X10096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiberiu from CLEVELAND, OH
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Harpers Ferry, WV
- Parts Used:
- WH43X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Non-agitation
My washing machine would not agitate. I looked online for the possible repair solutions under GE website. All I needed was my model number. I typed in the model number and it gave me possible solutions. I ordered the parts from part select. Once they came in, I then went online to find video of how to repair the machine. When I found the video I needed I began disassembling my machine. I pulled the agitator off with a brisk tug and used my socket wrench to unscrew the coupler nut. Once that was off, I installed the new coupler tightened the bolt and installed the agitator. I filled the machine enough for a small load and sure enough, it worked! I did not need to use the belt, but I will have it on hand if I need to. I saved on separate shipping. VERY PLEASED!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from BERKLEY, MA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Plastic pipe developed a tear and leaked drain water.
Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.
Was this instruction helpful to you?
Thank you for voting!