S2000D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from FLORENCE, SC
- Parts Used:
- WH44X21834, WH01X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Top had rusted out around the bleach dispenser and rusty water was getting in the clothes
Top panel was exactly what I needed and fit perfectly. To replace the top panel I first unplugged power. Removed control panel on top of machine. Removed front panel by placing a putty knife under front corners and pushing down on front panel. Removed two screws holding top panel to frame. Removed lid switch from top panel then removed lid from top panel. Lift up front of top panel and slide out of cabinet. Replaced new top panel in reverse order. The only thing I overlooked when ordering top panel was the plastic bumpers and rubber guides for the lid. Had to remove old parts from old top panel and use them. Overall job took about 45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Torrance from Southfield, MI
- Parts Used:
- WH12X10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My washer was overfilling
the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tompkinsville, KY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replaced drain pump on washer
Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Garden City, NY
- Parts Used:
- WH23X10030, WH1X2036
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
washer had heavy wet clothes left after spin cycle
The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Cambridge, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dampening straps were broken
Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Southbury, CT
- Parts Used:
- WH12X10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
water wouldn't stop pouring into the machine, would not spin water out
unplug machine and turn off water at the valve. the pressure switch is located behind the water level control knob. remove the knobs from the panel, then remove the panel on the top back of the machine and remove the wires from the pressure switch. unplug switch. attach wires to new switch and plug into place. replace panel and replace all the knobs.turn on the water valve and plug into outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Broken Arrow, OK
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Tub made banging noise when stopping from spin cycle
I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.
Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.
Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Ventura, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washer did not drain completely with water on floor, drain pump frozen.
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett F from Sag Harbor, NY
- Parts Used:
- WH13X10025, WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
A Leak Thought It Was A Hose At First But Still Leaked When Washer Was Not Running
Removed all visible screws to expose water valve . . Removed water valve , hose & water inlet and replaced with new . Straight forward and simple . Very fast delivery of parts that was huge . . Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drew from Apopka, FL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Tub straps broken caused excessive wabbling
Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jayme from drummonds, TN
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
My washer would not drain the water out.
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rochester Hills, MI
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Wash basin wobbled excessively
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from CORAL, MI
- Parts Used:
- WH12X10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water would not stop at prpoer level
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. put the new part in and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Dublin, TX
- Parts Used:
- WH13X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water continually ran into the washer when shut off and even when it was spinning
removed 4 screws on the top back of machine, undid 2 screws and the hoses, pulled old part out, put new part in. Walla!!!!washer is fixed!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Nokesville, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
some leak
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer
sincerely, a satisfied customer
Was this instruction helpful to you?
Thank you for voting!