WCCB1030J2WC General Electric Washer - Instructions

replaced pump to tub inlet hose.

removed old dampening straps replaced with new ones a total of 4 straps, took about 10 min, works great again.very easy to do. thank you.

I pulled the front off of the washing machine using a table knife to pop the clips. The drain hose had a hole big enough to put your finger in so we knew that was the problem. One of the clamps holding it on took a screwdriver to loosen the clamp, the other I used a pair of adjustable pliers to squeeze the ends together to loosen it. I pulled off the old part, ordered it, got it the next day and replaced it the same way I took it off. It was simple and the part was less than $10.

first I filled the washer max load to determine the problem, once I saw where the water was dripping I decided to remove the hose. I removed bottom of the hose, and the water from the tank started pouring out, I tryed to put the hose back on but started to get a pretty good electric shock, I then unpluged the washer and ran to garage for the floor squeegy. I then pushed the water out the side door. After cleaning and drying all rooms I sat down at the computer and ordered part. When the part arrived I removed clamp with pliers put both clamps on the new hose and installed. A very simple project and I ended up with a clean laundry room. Thanks "Brainy"

"Thought" the belt was the problem - ordered new belt - waited for belt to arrive - opened washer. Belt was in perfect condition - problem is the clutch. Next time husband will verify problem before ordering parts.

Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.

The belt is very tight. Use a zip tie to old the belt on as you work it around the large pulley. Once it is on remove zip tie and turn the pulley enough times to line up the belt evenly then your done.

Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!

I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!

I just popped in the new agitator. The coupler wasn't needed but I will keep it just in case.

I removed the agitator, replaced the agitator coupling. The guy at the appliance store where I was able to find the part said to check the splines on the inside of the agitator as well. Glad I did, the splines on the agitator were worn out too. So by checking both, if and when the problem occurs, REPLACE BOTH parts! This will save a lot of grief for you!

We couldn't get a repair to come out - were told to buy a new because it would cost too much to fix. I did not agree. I pulled the agitator off and discovered it was not working and the agitator coupler was spinning. I ordered both and put them in myself. My washer now worked like new! All for less than $100. The service guy wouldn't eve come out for less than $175 and that did not include parts!

First I removed the softener dispenser then I grabbed the agitator at the bottom and with a tug completely removed it. I took the new part out of the box and lowered it down over the hub in the bottom of the washer and gently pushed it until it snapped in place. Then I re-installed the old fabric softener dispenser and the job was complete.

With the instructions found online, this was a quick easy repair. I used youtube to have video to show the method. Used rope to pull up agitator, used wrench to loosen bolt and then put back together. Part was delivered really fast, I recommend Partselect.com for the parts you need!

I just did a google search and found a video that shows to use a zip tie to hold the belt to the big pulley and simply turn the drum and the belt goes right on. Then cut the zip tie off and you are ready to go. Took all of 3 minutes to change the belt from start to finish.