GTWP2250D1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Hollywood, FL
- Parts Used:
- WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annamarie from FORT LORAMIE, OH
- Parts Used:
- WH43X10032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not agitate
Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the problem.Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Spring city, PA
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bad lid switch
Watched the how to video, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oraila from RINCON, GA
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken part
We pulled out the old parts and then we got the new parts and we put them in,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifton from WAUKEGAN, IL
- Parts Used:
- WH41X22935
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Swanton, OH
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
Washer tub was banging around violently during spin cycle
After doing some research on the problem I decided that the rubber tub dampers were probably the problem. Replacing them was simple and straight forward after watching the video. A test spin after installation revealed that the problem still existed. This time I watched the bottom of the tub with a flashlight as the spin cycle began and I discovered that the concrete counter-weight was loose on its platform. General Electric had attached a 5 lb concrete block to the tub support with two self tapping sheet metal screws that had stripped out. I screwed the screws back in and added two nuts to the protruding screw bottom and locked them together. Problem solved. The main difficulty in this repair is reaching to the back of the washing while laying on the floor. And sharp edges on everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from bradford, VT
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Duanesburg, NY
- Parts Used:
- WH12X10334
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer lid sensor stopped working, thus, would not spin, thinking lid was open
This was easy and took maybe a half-hour. The harder part was pulling the front panel off (up) to access the insides. Simply snipped the wire to the old sensor and spliced the new wire and inserted the new sensor. Worked perfectly and saved me $400? on a new washer! (Cover panel is slightly bent, did not re-snap in, so it's loose; I don't care about the looks, so I will screw metal screws using a hinge to close it.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Livingston, LA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
1 Broken tub dampening strap and 1 about to break
Removed the front panel (retainer clips), removed two screws holding the top panel and door, removed all 4 dampening straps and replaced them with the new straps, put the components back in reverse order of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Hazard, KY
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Hose had developed a slit in the seam nearest to the tub and was pouring out the water flooding the basement where the washer is located.
Lay the drain pipe lower than the tub to remove any excess water in the tub and lines. Loosened clamp on the tub side with a screwdriver then removed hose from the tub. I used pliers to pinch clamp and remove hose from pump. To install hose put clamps on hose then mount to the pump and the tub then tighten clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Sebring, FL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer would not spin
removed old dampening straps replaced with new ones a total of 4 straps, took about 10 min, works great again.very easy to do. thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andre from huntersville, NC
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
leaking hose
turned washer on it side took bottom off removed hose and replaced it with the new one. so very happy i tried it , works great like before. thanks for the easy to find diagram of parts.
Was this instruction helpful to you?
Thank you for voting!