Models > GTWP2250D1WW

GTWP2250D1WW General Electric Washer

Jump to:

Find Part by Name

Diagrams for GTWP2250D1WW

Viewing 4 of 4

CABINET, COVER & FRONT PANEL

CONTROLS & BACKSPLASH

SUSPENSION, PUMP & DRIVE COMPONENTS

TUB, BASKET & AGITATOR

Manuals & Guides for GTWP2250D1WW

Click to download

Install

Installation Instructions

Most Popular Parts for GTWP2250D1WW

Viewing 12 of 78

Dual Action Agitator

$61.32

This is an authentic agitator for your washer, responsible for moving clothes inside the tub. Please note, it does not come with the fabric dispenser, so you will need to either transfer the old one t...

Order now and your part arrives by May 10

Tub Seal

$20.72

If your washer is leaking when it is filling or agitating, you may need to replace the tub seal. The tub seal is found between the transmission and the outer tub in your washing machine. This genuine ...

Order now and your part arrives by May 10

Split Ring

This split ring is two inches in diameter.

Tub Bearing Washer

$15.26

Order now and your part arrives by May 10

Tub Bearing

$41.78

The tub bearing secures the spin basket in the tub assembly of a washer. It is located on the bottom of the outer tub. A common symptom of a worn tub bearing is a very loud noise (including a grinding...

Order now and your part arrives by May 10

Agitator Coupling

★★★★★

(1)

$28.91

Bolt not included. This part connects the transmission drive shaft to the agitator base.

Order now and your part arrives by May 10

Lid Switch with Wire Harness

$41.78

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

Pump to Tub Inlet Drain Hose

$25.10

This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.

Order now and your part arrives by May 10

Socket Rod Support - White

$15.26

This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...

Order now and your part arrives by May 10

Screw - 1/4-20 MCH HXW 5/8 S

$8.70

This is a replacement screw for your washer. The screw has a hex head and is approximately 1 inch in length. The washer portion of this screw is approximately 1 inch in diameter. This part is sold ind...

Order now and your part arrives by May 10

Front Suspension Rod & Spring Assembly - Blue

$43.92

Sold individually. This part is used to keep your tub upright and somewhat level during the different cycles.

Order now and your part arrives by May 10

Locking Clip

$15.26

Sold individually.

Order now and your part arrives by May 10

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for GTWP2250D1WW

Viewing 11 of 11

Leaking

Fixed by these parts

How to fix it

Will not agitate

Fixed by these parts

Marks left on clothes

Noisy and Marks Left on Clothes

Touchpad does not respond

Fixed by these parts

How to fix it

Videos for GTWP2250D1WW

Viewing 8 of 16

Replacing the Tub Dampening Strap

Replacing the Dual Action Agitator

Replacing the Tub Bearing

Replacing the Tub Seal

Replacing the Tub Bearing Washer

Replacing the Lid Switch with Wire Harness

Replacing the Rear Suspension Rod & Spring Assembly - Red

Installation Instructions for GTWP2250D1WW Provided by Fix customers like you

Viewing 3 of 164

Customer:: Brian from Millerplace, NY
Parts Used:: WH12X10334
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins

washing machine would not go through all cycles or agitate

After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.

230 of 293 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Michael from Itasca, IL
Parts Used:: WH43X10034
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Blades broken off agitator

Simply put hands, one under each side of the agitaror and pulled up. The part snapped off very easily. I then placed the new part in the tub and pressed down. Extremely easy, should have done it sooner!

73 of 90 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from Covington, PA
Parts Used:: WH01X39337
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

loud noise upon aggitation

replaced Tub dampeners Straps.

18 of 23 people found this instruction helpful.

Was this instruction helpful to you?