GTWP2250D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- B. from WILLISTON, FL
- Parts Used:
- WH02X10383, WH02X10265
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
water was dripping down onto the belt and stopping movement
front back and top have to come off, but contrary to 'youtube' instructions, 'nothing' has to be disconnected, if the washer is pulled away from the wall and power unplugged things can be unscrewed and pushed back enough to pull the inner tub out and get to the seal without disconnecting water lines wires or anything else.. the main shaft nut is aluminum and the shaft is 'castellated' so alittle penetrating oil on it and a short 10" pipe wrench in conjunction with a 2lb sledge busted it loose easy enough so i didnt need to buy a spanner .. the seal was easy to get out with a couple of screwdrivers wedged in the sides .. the old split ring crumbled upon removal also so get one of those .. i lucked out on the washer that goes with it and mine was still usable but if it was rusted any more than it was i wouldve needed that also .. so good idea to get the 3 items if your doing the seal - seal, split ring, and washer - another thing, i cleaned everything up good, knocked everything off with a brass brush, polished the shaft seal area with some 600 grit and then lubed the seal with silicone grease thinking it might be hard to get in .. it wasnt .. and it leaked slightly until i did several loads .. in hindsight it would be better to 'lightly' coat the outer edge of the seal that mates to the tub with a good silicone gasket maker, the inner lips with the grease would be fine ... so thats about how it went, parts came quick and i had it all fixed up in a couple of hours .. cleaning things as i went probably took longer than the wrenching ..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Casper, WY
- Parts Used:
- WH2X1197, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
it was leaking
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MARSHALLTOWN, IA
- Parts Used:
- WH12X10614C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Machine would lose power and shut itself off.
Unplugged machine. Used tape markers to identify knobs then removed control knobs with vigorous straight pull. Unscrewed three screws on rear of control panel face and tilted control panel over with a small sideways slide, to expose circuit board. Laid new circuit board alongside old and transferred jumper block and wiring terminals from old board to same positions on new. Unscrewed old board and removed. Put in new board and tightened screws. Replaced back panel and knobs. Plugged in machine and tested. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifton from WAUKEGAN, IL
- Parts Used:
- WH41X22935
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hollywood, FL
- Parts Used:
- WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from mazeppa, MN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken dampening straps
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from BEACHWOOD, OH
- Parts Used:
- WH41X365
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing machine never stops filling and thus overflows
Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.
Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ELMIRA, NY
- Parts Used:
- WH41X365
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Port Hueneme, CA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Was this instruction helpful to you?
Thank you for voting!