GTWP2250D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from BEACHWOOD, OH
- Parts Used:
- WH41X365
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing machine never stops filling and thus overflows
Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.
Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ELMIRA, NY
- Parts Used:
- WH41X365
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CONYERS, GA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifton from WAUKEGAN, IL
- Parts Used:
- WH41X22935
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from BRIMFIELD, MA
- Parts Used:
- WH43X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Not agitating, free spinning agitator
Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from STANFIELD, NC
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Replacing drain pump
The job was rather simple. After removing front panel with the aid of a putty knife to push back the spring clamps under the top panel, the pump is in plain view. Remove the two mounting screws and push back the spring clamps that secure the connection hoses. Squeezing the spring clamps that hold the hoses onto the pump can be a bit troublesome so I removed the spring clamps completely and replaced them with radiator hose clamps which made the job a whole lot easier. Replaced the front panel and the job was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MARSHALLTOWN, IA
- Parts Used:
- WH12X10614C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Machine would lose power and shut itself off.
Unplugged machine. Used tape markers to identify knobs then removed control knobs with vigorous straight pull. Unscrewed three screws on rear of control panel face and tilted control panel over with a small sideways slide, to expose circuit board. Laid new circuit board alongside old and transferred jumper block and wiring terminals from old board to same positions on new. Unscrewed old board and removed. Put in new board and tightened screws. Replaced back panel and knobs. Plugged in machine and tested. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LEXINGTON, OH
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from FLORENCE, KY
- Parts Used:
- WH41X10096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Was this instruction helpful to you?
Thank you for voting!