GTWP2000F1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Foris from Nome, TX
- Parts Used:
- WH43X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Washer would not agitate.
Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CHARLESTON, SC
- Parts Used:
- WH13X10053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would not mix properly and/or fill properly
Easy as can be. Similar but not exactly like the YouTube videos, but close enough. Biggest problem was pulling the filler tube off of the mixer and re installing the tube. Nothing to get worked up about.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from DOVER, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Tub shacking
Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCIS from BRICK, NJ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Noisey,out-of-balance spin cycle
Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from PLAINS, MT
- Parts Used:
- WH41X22935
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Small wire had tried spin out of drain pump. Wore pin hole in the rubber drain hose....
Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from LA QUINTA, CA
- Parts Used:
- WH12X10334, WH01X10302, WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
tub moving allover the place
replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donn from WIMAUMA, FL
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fitted sheet got stuck under the agitator
Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Delbarton, WV
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
My washer started leaking water out of the bottom.
I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from Berkeley, CA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from West Memphis, AR
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer flooded my laundry room!
Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Chesnee, SC
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Had a small water leak gettin into the drip pan.
Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from St. Cloud, MN
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Leaking hose (had a rip in it)
First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Washougal, WA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
hose had a crack in the crease causeing leak .
I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Utica, NY
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washed my daughter's toys and broke the agitator
Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.
Was this instruction helpful to you?
Thank you for voting!