GLWN5550D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beverly from Casper, WY
- Parts Used:
- WH2X1197, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
it was leaking
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ELMIRA, NY
- Parts Used:
- WH41X365
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifton from WAUKEGAN, IL
- Parts Used:
- WH41X22935
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CONYERS, GA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosemary from holyoke, MA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
the belt is so tight
I heard this is a tool you need to get that belt on with out slipping off. we thought we had the wrong size belt it as impossible at first to get the belt on. what a struggle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hollywood, FL
- Parts Used:
- WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Murphy, TX
- Parts Used:
- WH2X1197
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
The machnica had recently developed a rumble during the spin cycle
The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Reno, NV
- Parts Used:
- WH41X10096
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leak under the washer
After noticing the leak, I moved the washer out to try to find the source. In the process, the Drain Hose Extension broke in two. As an emergency repair, I put the two halves together with duct tape. After running the washer again to try and find the leak, I discovered that it must have been the Drain Hose because now there was no leak. I then ordered a new one from PartSelect and replaced it with the repaired item.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Duanesburg, NY
- Parts Used:
- WH12X10334
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer lid sensor stopped working, thus, would not spin, thinking lid was open
This was easy and took maybe a half-hour. The harder part was pulling the front panel off (up) to access the insides. Simply snipped the wire to the old sensor and spliced the new wire and inserted the new sensor. Worked perfectly and saved me $400? on a new washer! (Cover panel is slightly bent, did not re-snap in, so it's loose; I don't care about the looks, so I will screw metal screws using a hinge to close it.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miramar, FL
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
A lot of water was coming out underneath the equipment.
Steps:
1.- Open the front panel by pressing down (with a spatula) the 2 metal locks located between the front and top panels.
2.- Remove the drain hose located int the lower right and at the bottom using a set of pliers and a nutdriver.
3.-Install the new drain hose.
4.-Reinstall the front panel
The installation itself took me less tha 15 minutes.
Since I had opened the the front panel, I took rthe oportunity to air clean and dust off the equipment.
1.- Open the front panel by pressing down (with a spatula) the 2 metal locks located between the front and top panels.
2.- Remove the drain hose located int the lower right and at the bottom using a set of pliers and a nutdriver.
3.-Install the new drain hose.
4.-Reinstall the front panel
The installation itself took me less tha 15 minutes.
Since I had opened the the front panel, I took rthe oportunity to air clean and dust off the equipment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andre from huntersville, NC
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
leaking hose
turned washer on it side took bottom off removed hose and replaced it with the new one. so very happy i tried it , works great like before. thanks for the easy to find diagram of parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Livingston, LA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
1 Broken tub dampening strap and 1 about to break
Removed the front panel (retainer clips), removed two screws holding the top panel and door, removed all 4 dampening straps and replaced them with the new straps, put the components back in reverse order of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy from sulligent, AL
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
busted drain hose
It was really easy to replace i removed the old one & sliped on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bucyrus, OH
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
leaking water from bottom
replaced pump to tub inlet hose.
Was this instruction helpful to you?
Thank you for voting!