Models
>
GLWN5550D0WW
GLWN5550D0WW General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GLWN5550D0WW
Viewing 4 of 4
Manuals & Guides for GLWN5550D0WW
Click to downloadInstall
Installation Instructions
(1.65MB)
Manual
Owner's Manuals
(3.82MB)
Manual
Owner's Manuals
(2.01MB)
Keep searches simple, eg. "belt" or "pump".
$9.61
This is a single tub dampening strap for a washer. It is recommended to replace all 4 tub dampening straps at the same time, to ensure even wear. This part supports the tub and minimizes vibration by ...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$27.09
This is a genuine OEM drain hose for your top-load washing machine. It is made with a flexible and corrugated black material, and measures 57-inches in length. The purpose of the drain hose is to move...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$16.73
If your washer is leaking when it is filling or agitating, you may need to replace the tub seal. The tub seal is found between the transmission and the outer tub in your washing machine. This genuine ...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$25.75
This is a 6-rib washer drive belt. It is sourced directly from the original manufacturer and constructed with a durable Poly V material. This part connects the drive motor to the drive system that tur...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$27.53
The tub bearing secures the spin basket in the tub assembly of a washer. It is located on the bottom of the outer tub. A common symptom of a worn tub bearing is a very loud noise (including a grinding...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$53.87
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$16.95
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$13.08
This is a water pressure switch hose, also known as the air dome tube, for your washer. It is made of clear plastic and is sold individually. The hose transports water to your water pressure switch, s...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$53.29
The purpose of the triple water valve is to properly fill your washer with water by controlling the hot and cold water going into the tub. If your washer is overfilling or not filling, you may need to...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
$12.61
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
In Stock
Order within the next 1 hr and 49 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas
January 8, 2023
Evn while filling it makes a noise like metal scraping
For model number GLWN5550D0WW
Hello Thomas, thank you for contacting us. If the noise is just during the filling, we would recommend checking the water pressure and the water inlet valve, part number FIX3652834. If it makes noise while running, the most probable cause of the issue is a damaged tub bearing, part number FIX271510. Over time, the bearings that support the tub can wear out and cause a scraping or grinding noise. If the bearings are worn, they will likely need to be replaced. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Was this helpful?
Thank you for voting!
Related Parts:
Thomas
January 8, 2023
Makes a metal to metal sound s like tub is rubbing on one side
For model number GLWN5550D0WW
Hello Thomas, thank you for contacting us. The issue is most probably related to the tub bearing, part number FIX271510. Over time, the bearings that support the drum can wear out and cause a metallic noise. If the bearings are worn, they will likely need to be replaced. Also, check the Tub Dampening Strap, part number FIX271100. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for GLWN5550D0WW
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Millerplace, NY
- Parts Used:
- WH12X10334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
washing machine would not go through all cycles or agitate
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from barry, IL
- Parts Used:
- WH01X10302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken drive belt
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the leg
... Read more
s in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Meridian, ID
- Parts Used:
- WH01X10302
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while
... Read more
moving belt so it is properly seated on pulley.
Read less
Was this instruction helpful to you?
Thank you for voting!