WBB2090G8WW General Electric Washer - Instructions

I just removed the clip and took off the old knob. I than put the new one on and replaced the clip.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

replaced them & working fine now....

Opened lid and place on agitator ... finished

Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

You tube is the only way to go!

This sounds like an easy fix to replace the shaft seal after watching the video, Oh how WRONG was I.....Firstly the video and parts list show just pull the agitator off..... NOOOOOO the bolt (Screw) is deep inside the agitator and that has to be removed to get the agitator off.....maybe in some models they have changed this poor design but not mine....As the screw is open to all the water and detergent guess what, it was so corroded you could get a sock to grip on it. Only solution was to cut the agitator in half at the bolt head level to get a vice grip on the rounded bolt head to undo it........It doesn't stop there, then you have to remove the fins in the remaining part agitator to get get the vice grips on. OK so far so good, now try and undo the big left hand thread nut....good luck, totally corroded, tried penetrating oil, heating it up you name it, nothing. I had a 1 11/16 socket but you need a deep socked as the shaft protrudes too far...solution drill the nut in three places to break it off the thread....OK so far we are winning....Now try to get the split spacer off the corroded shaft, no way was that going to happen it did eventually span in half so had to buy that too.....NOW WE STILL have to get the washer off the shaft...Run out of space to continue...

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.