WBB2090G8WW General Electric Washer - Instructions

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

Removed the top panel and twisted the old pressure switch off counter clockwise. Then disconnect the electrical plug and the plastic hose attached to it. Do the reverse for putting the new one on. Very easy repair that you only need a screw driver for.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.

Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.

Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.

No problem with the replacement. Great company to order parts. Received them as expected.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.