GFWN1000L1WW General Electric Washer - Instructions

Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.

The repair video was almost perfect. I would not have even attempted the repair without the video as I am not a handyman at all. The diagnostic feature based on the symptoms was invaluable. I originally took the front of the washer off because I thought the rubber seal around the door was leaking.It was like 67% of the problem. But after checking the front seal carefully, I determined it wasn't. The next most likely issue as only rated 19% but when the water inlet pipe, I was actually tickled to see a crack in the plastic pipe. I ordered on line on Monday and with the cheapest shipping, I received my part in the mail on Thursday. I would highly recommend using Part Select for diagnostic, parts and repair. I will definitely use again. If I could make one recommendation to Part Select, it would be to do a close up during the video when the technician is working with a part, i.e., the wiring that goes around the rubber seal.

Did not have to use the new pump filter. The old one finally worked. I probably didn’t screw it in tight enough.

The white door plunger broke after 3 years of use. After replacing the door plunger the door still would not close. so I also ordered the door lock part for inside the washer. This was also an easy replacement but far more expensive. A thing to note. If the door plunger breaks you may need to reset you locking piece. and save your self 130 dollars. To do this. remove the top panel of the washer. remove the control panel. remove the spring ring around the rubber seal. disconnect the door locking piece and remove from washer. now use a hook or stiff wire and loop inside the door plunger hole and pull the lock out. if it wont release ensure the white piece on the bottom is lowered all the way. This is also possible to reset with out removing but you wont be able to check the white piece(the lock holder). What ever you do do not take apart the locking piece it has lots of little parts an will give you nightmares.

My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! Hook up the drain hose with pliers and screw the motor to the frame and that's it!

Removed top cover, loosened front door cover, removed & replaced old cracked plastic 'water inlet tube', reinstalled front door unit & top cover. Very tight space to work in when not completely removing front door unit.

Sandblasted spider to thoroughly clean it and increase ductility.We used aluminum foil covered in 5200 on one side to cover holes eaten through spider. Then glued the spider to the drum and filled inside rim of spider with a nice layer of 5200. If the spider was made of stainless steel, the washer would still be running great. Thanks

Removed top and front control panel. Shut off water, disconnect water lines at front and dispenser. Remove dispenser. Remove water inlet pipe by pulling out of boot. Install new pipe.Reverse proceedure. Note, these pipes may tend to split on the bottom.

You probably won't want to publish this but it worked. The baffle on the GE washer I have required a complete tear down of the machine's front and outer waterproof drum to get a tiny little screw out. Very poor design if you ask me. And, I was not about to pay a technician for a massive overhaul to get a 3/8" long stainless screw off the broken remains of the baffle. So, I measured how far over the screw was from the pipe that feeds detergent, softener and bleach into the drum. I drilled a 3/8" hole in the outer drum. After removing the screw and installing the new baffle (which took all of about 2 minutes), I put a 3/8" hole plug I bought at Lowes into the hole with two part plastic epoxy. Then I covered the entire hole plug with a crown of epoxy. Five minutes later when the epoxy set, I ran a load of clothes. It ran perfectly and did not leak. I know. I know. This is not what you would recommend to your readers but it worked. I was brought up fixing everything around the home and any effectie shortcut was/is used. Oh,by the way, if you know which GE engineer thought up the design for this baffle installation, whack him on the head once.

I watched the video and followed the instructions. First remove power. Remove the rear cover from the control panel and the top cover. Then remove screws that secure the control panel to the frame and remove the control panel. Remove the bottom cover. Then remove the lock ring that holds the rubber boot to the front panel. Remove the door and remove the water inlet pipe. Assemble the machine and run a test cycle.

I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.

1) Remove door hinge cover. 2) Remove hinge door plate. 3) Remove hinge door pin using a hammer and striking tool if necessary. 4) Using needle nose pliers, remove gasket inside clamp from the door boot seal. There is a spring at the bottom that should allow you to pry this part out and off. 5) Pull the door boot seal away from the exterior cabinet to allow access to the hinge. 6) Remove the hinge screws 7) You should now be able to remove the hinge. 8) Install new hinge and reverse steps to reassemble.

After getting error message from washer, Looked it up and found if the water lines are find, then replace the water valve. After replacing the valve, everything works fine.

First I removed the excess water by using my shop-vac both inside the machine as well as near the bottom drain valve. After cleaning out that valve (which somehow had accumulated a pair of underwear) it was apparent that the drainage pump motor was no working (loud hum, not spinning). Replacement was easy, folowing instructions found everywhere on-line. Now the machine is working perfectly again.

Removed old pump and replaced. Did not want to wait 2-3 weeks for a repair person