WCSR4110TBWW General Electric Washer - Instructions

Remove screws from front panel, removed two screws holding valve in place, "found it would be easier to remove upper back panel also to get the hose clamp back on", Disconnected wires and reconnected to new valve, put the screws in rear and front panel, hocked up the supply lines and done. Worked great. Took me maybe 5 min. from start to finish

1. Disconnected Water Hoses (Hot & Cold). Needed a wrench to initially loosen and then used my hand to remove them.
2. Opened the Control Panel, by unscrewing and removing the cover.
3. Pulled out the two electrical plugs (labelled which one goes where with a tape) connected to the old water valve.
4. Pulled out a tiny hose connected to the old water valve (by loosening a clamp that held the hose tight with a pair of pliers).
5. Removed the old valve, put in the new. Reattached the hose, the electrical plugs, closed the control panel, and reattached the hot & cold water hoses.
6. Problem solved.

I first placed a rope under the fins of the agitator and used a 2X4 board to pull up the agitator which needed very little force to release itself from the agitator coupling. I removed the nut holding the agitator coupling, removed the stripped agitator coupling. Installation was just the reverse process, inserted the new agitator coupling, placed and tightened the screw, and pressed down the agitator over the agitator coupling and I was done. Over time for the repair was between 5 and 10 minutes, very easy, and I have no experience repairing washing machines.

took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!

I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.

Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.

I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.

PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.

***Partselect.com had my ordered part delivered within 3 days.*** First, I pulled up on agitator and removed it. Then, loosened bolt on coupling and removed it. Replaced with new coupling, placed and tightened new longer bolt that came with new coupling. Replaced agitator and started laundry.

The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done

1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.

I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.

We removed the agitator then the bolt holding couplier. The inside of the plastic couplier had stripped after 5 years. We cleaned around the metal part of the agitator then installed the new GE plastic couplier, put in the bolt & replaced the agitator. The machine works better than ever.

The GE website said this part had to be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.

I just added the agitator coupling and screwed it in.

This site is amazing. I entered my model# and described the issue and they identified the part. I watched the repair video once and made the repair in the same time as the video. One caution. Make sure you keep track of which wires came from which connection. Not a big issue but you don't want to get them switched.

There was a video online right below the part that was recommended that I needed. The video was very easy to understand. After watching the video I just simply did the repair exactly as was instructed and within 15 minutes the repair was completed and the washer works like new. Thank you so much!!!!

Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!