WNCD2050A0WC General Electric Washer - Instructions

My husband remove the agitator and found that it was worn. I googled the problem and one of the websites that came up was PartSelect. My husband watched the easy to follow video and had me order the Agitator Coupling Kit. It arrived in just two days. It took him 15 minutes to install and I started washing immediately. It cost us $13.22 and saved us $800 to $1200 if a new washing machine would of had to be purchased. The washer is 15 years old and now with this repair will hopefully continue to wash for a few more years! Thank you PartSelect!

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling

Resigning myself to the fact that the washer was broken and I would need to buy a new one, I decided to pull it apart to see if I could see what the problem was (why not if your getting a new one anyway) Once I muscled the agitator off and undid the screw I discovered that the agitator coupler sat on a metal piece that had grooves. Alas...the coupler was worn...there were no grooves left inside the plastic piece. Wondering if I could even find this part I wondered onto this website, plugged in the part number and there it was with pictures and measurements and cheap! Needless to say I ordered it, why not, if it doesn't work I will buy a washer anyway. The part arrived within days. I unpacked the box, opened the plastic, slid it into place, tightened the new screw, replaced the agitator, plugged it back in, started it up and the washing machine was agitating like new. I wrote this long story because the repair was so easy it's not even funny, and I was just going to buy a new washer...

Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)

take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.

took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

easy to repair. instructions (with pictures) were included with the part. part came super fast.

Reaching into the washer I placed both hands on the bottom of the agitater 180 degrees apart and lifted the agitater straight up out of the tub. Using a 7/16 socket I removed the coupling kit. The new one slid right on. I secured it with the new bolt supplied with the kit. The agitater went right back on the new coupler and I was done. Fast, simple and inexpensive. Thanks so much to Part Select.

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!