WNSR3120W0WW General Electric Washer - Instructions

Just push knob on less than 4 seconds

At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push

I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.

I followed the easy instructions on the video site for installing a knob and clip on a GE washer. The knob and clip were not available to find locally. I was told at a part store that a whole new operating switch had to be replaced which would be approximately $180 to buy. After visiting your site, and viewing your easy instructions, only a knob and clip were needed. Delivery was in 3 days. Very easy installation. Saved bucks. Pleasant experience.

I pulled the clip out of the old knob and removed the knob. I then set up the clip on the new knob so it was partially engaged and would still allow the knob to be pushed onto the stem. I then aligned the new knob into place and used a pair of needle nose pliers to push in the clip and secure the knob. It was fast and fairly easy. Now the whole mechanism works like when the washer was new.

Took new one out of package, and push it on. 4 seconds!

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.

I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz

I took of the old clip an broken piece of the knob, and removed the selection plate, and push on the new knob and clip, using my pliers.

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .

ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.

I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.

Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.

Watched video,removed clip and pulled knob off.

I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.

Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.

I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.

PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.