WCSR4110TBAA General Electric Washer - Instructions

I removed the fabric softener cup and lifted up on the agitaotor till it slid off. I then removed the bolt that held the agitator coupling in place. I then worked the coupling off, wiggling it side to side until it slid off. Then I slid the new coupling on and replaced the bolt. Lined up the agitator and slid it back on. Then replaced the fabric softener cup. Job could not have been any easier.

I took the plastic agitator out and checked the agitator coupling underneath. I unscrewed the agitator coupling and looked inside. It appeared that the grooves on the agitator coupling which attaches to the stem had become stripped. I ordered the $6.00 agitator coupling and screwed it back onto the stem. The plastic agitator slipped back onto the coupler and it worked perfectly after that.

Agitator came off easily, but the agitator coupling was a little bit hard to remove. I have to yank it hard to be able to remove it. Putting the new part in is a bit hard too. I had to use a hammer to put it in. (with a piece of wood in between). Tried it with a small load and We're back in business. It was a pleasant experience to do business with you guys. Thanks for the quick turnaround.

To get the old agitator off I first used two pieces of laundry line rope to hook under the fins of the agitator on each side. Next I laid a 5 foot long 2 X 4 across the top and tied the ropes on. I filled the washer with 5 or 6 inches of extremely hot water to help loosen everything up and used leverage to pop the old agitator off. After that I used a socket set to remove the bolt from the top of the agitator coupling and took it out. I then put the new coupling in, replaced the bolt and lined up the agitator and slid it back on until it clicked and locked into place. The washer works great.

I was very disappointed that this washing machine was broken since it is the second GE washer I have had in this house and the home is only 11 yrs old. I went to the Parts Select website and used the repair information to diagnose the problem and order the part. The part was about $12 including shipping and arrived in a few days. Installation was quick and easy. Overall a very good experience since I was asssuming a broken transmission and new washer. Thanks Parts Select!

removed old dampening straps replaced with new ones a total of 4 straps, took about 10 min, works great again.very easy to do. thank you.

My husband remove the agitator and found that it was worn. I googled the problem and one of the websites that came up was PartSelect. My husband watched the easy to follow video and had me order the Agitator Coupling Kit. It arrived in just two days. It took him 15 minutes to install and I started washing immediately. It cost us $13.22 and saved us $800 to $1200 if a new washing machine would of had to be purchased. The washer is 15 years old and now with this repair will hopefully continue to wash for a few more years! Thank you PartSelect!

Replaced the Dual Water Inlet Valve. Took about 15 minutes to take the old one off and put the new one back on. the cold water started comming out like it should,it also seemed to have more pressure and filled faster. We have had the washer for over five years and it seemed that it took forever for it to fill when we did a load. So by replacing the valve it fixed the problem of no cold water comming out and the slowness of filling. It seems to be filling faster.

Easy as it gets. I did this repair while playing Wii with my 8 year old and cooking supper... Still no more than a 10 minute fix.

Place a towel on one side of the washer so you won't scratch it.

Tie a loop of rope around the middle of the agitator between the upper and lower fins. Wrap the other end of the rope around a 2x4 ( I used a level), or anything similar and wind it around until the 2x4 is pulled down level with the top, keeping one end on the towel.

Yank the other end firmly a few times, and the agitator will seperate from the coupling. I had to snatch it pretty hard.

I removed the 7/16" bolt from the coupling, pulled it off the spline and replaced it with the new one.

The agitator slid right back into place with no trouble, and it is good as new.

What seemed like an expensive repair, or even the need for a new appliance was essentially removing one bolt and a replacing a $6 part.

Thanks!

I noticed that the agitator would spin without any resistance and must be stripped. I pulled the agitator straight up and it came right off. I then used an open end wrench to remove the bolt securing the agitator coupler to the metal spline. It came right off and was obviously stripped. Upon receiving the new coupler, slipped it straight on and tightened the coupler. Placed the agitator on the coupler and tested the washer, it worked. Very easy. My wife was ready to buy a new washing machine and I fixed it with a six dollar part.

Popped the agitator off, removed the bolt, pulled coupler straight up. Reversed steps. Done in under 5 mins.

Removed the front panel (retainer clips), removed two screws holding the top panel and door, removed all 4 dampening straps and replaced them with the new straps, put the components back in reverse order of removal.

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

I lifted the agitator stragiht up. removed agitator coupling bolt w/pliers. went on Partselect.com to order replacement coupling, which supplied me with exploded diagrams, entered part number in box at the bottom of the screen and waited 2 days. It then took me less than 5 minitues to complete.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.