WHDVH660H0MS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynn from Kennesaw, GA
- Parts Used:
- WH08X10036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Door leaking due to tear in boot seal
Accessing the door seal was routine. Removing top and front covers was easy. Lower front cover was a challenge because the leaking door caused the screws holding the panel to rust, so extra effort had to be used not to strip the screw heads. Seal removal was easy, replacing the seal was much more difficult. The majority of the repair time was spent attaching the new seal to the drum. It became a tedious task with a large amount of trial and error. Replacing the front spring clamp also takes some time. Eventually I completed the repair and fixed the problem. I will say that if the washer breaks again, it's going to the dump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from Bend, OR
- Parts Used:
- WH08X10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door Boot Seal was ripped
Called a Repair Man, he came installed the part and I now have a working washer once again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RON from APPLE VALLY, MN
- Parts Used:
- WH13X10023
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Hot water hose leaking, it was cross treated (twice) by the installer, would not warranty it the second time.
Followed your instruction, very easy. I installed Camco 90" & 45" Brass elbows to relieve strain on hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Wylie, TX
- Parts Used:
- WH07X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Rattling during the spin cycle
After I disconnected the power and water and turned the washer around. I removed the back panel cover and the top and back panel to get to the pulley wheel. Once I remove the retaining nut and pulley the wheel off the spindle, i compared the new and the old parts and noticed the obvious wear on the old part, luckily the spindle was not damaged and still functional. Placing the new pulley wheel was a little more challenging. Once I seated the pulley wheel with a gentle tap from a rubber mallet. I fitted the lock nut onto the spindle and continued seating the wheel evenly using the nut to the prescribed torque pressure. After I reassembled the washer and reconnected the water and power, tested the washer, and success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from Zebulon, GA
- Parts Used:
- WH41X10118
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water leaking from the door boot area.
I watched the video and followed the instructions. First remove power. Remove the rear cover from the control panel and the top cover. Then remove screws that secure the control panel to the frame and remove the control panel. Remove the bottom cover. Then remove the lock ring that holds the rubber boot to the front panel. Remove the door and remove the water inlet pipe. Assemble the machine and run a test cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luciano from Houston, TX
- Parts Used:
- WH41X10118
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Washer Was Leaking A Lot Of Water
I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.
Was this instruction helpful to you?
Thank you for voting!