ETW485ASW0WB General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PAUL from LANCASTER, CA
- Parts Used:
- WH43X34257, WH43X31240, WH43X24454
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator bad had cracked and broke, catching pants tie strings.
Able to unscrew center auger real easy using oil filter wrench (for grabbing old auger easily). Used my deep socket wrenches with a speed handle to remove bolt. Then swapped everything out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Oxford, GA
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer would not drain
Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from BOSSIER CITY, LA
- Parts Used:
- WH43X24454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inner part of fabric softener dispenser base broke off
looked up part not exactly easy. that was the hard part. it was delivered next day and just had to pop into place extremely easy instalation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Kalispell, MT
- Parts Used:
- WH43X31240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The washer agitator/auger broke off of the base during a wash cycle. The small plastic clips broke off the auger so it couldn't be put back on the base.
The agitator/auger was easy to replace - it just snapped into place. We watched a YouTube to make sure to lock it into the counter clockwise direction.
This saved lots of time and the cost of a repair person to come.
This saved lots of time and the cost of a repair person to come.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Naples, FL
- Parts Used:
- WH44X24385
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced GE Washer lid
Removed parts from old lid (bumpers, switch component and hinges), removed old lid, then replaced parts on new lid. The new lid fit perfectly and looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Anderson, CA
- Parts Used:
- WH01X27538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Clothes very wet at end if cycle
Pulled the washer away from the wall and tipped it back. Removed 3 screws holding the belt cover on. Pulled the old belt off and found it was stretched and coming apart. Put the new belt on the small pulley and put a small screwdriver between the large pulley and belt. Rotated the large pulley to get the new belt fitted. Reinstalled the belt cover and put the washer back. Problem fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!