WISR309DTCWW General Electric Washer - Instructions

Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.

Pretty simple, really, I removed the broken actuator with a pair of pliers and replaced it with the new one, no fasteners required. A perfect fit, too.

Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!

First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).

Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.

I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .

The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.

Check on internet on how to use a putty knife to remove the front panel (slip it into the crack between the top lid and front panel). Then you can see the straps that are broke, figure out which screws to remove to gently lift the top lid to get at the pieces holding the straps in. Pretty simple, just remember to unplug the machine before starting.

Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure

First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.

pulled up on agitator and it came off and replaced it with the new one

Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.

Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!