GTW465ASN2WW General Electric Washer - Instructions

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

Took the belt cover and then replaced the pump. Did a dry run and everything was fine.

Easy fix. Take out the two screws on the backside of the control panel and remove control panel out of the way. You will need a long shaft nut driver or 1/4 inch socket extension to be able to get to the nuts, one on each side of the back of the control panel. The water inlet valve is right there in your face. Easy to remove and replace. Remember to save the small O-ring in the center of the top of the valve and reuse it. Oh, by-the-way, shut the water off first and unplug the washer. Replacement part was a perfect match.

Instructions were fairly good, line up holes and push a phillips head screwdriver thru auger then twist it off. Problem is you can only use a short screwdriver due to space limitations, and it is or at least for me was impossible to twist the auger off as directed, but after I lost my temper and gave the screwdriver a good thump (auger was already broke, what's the harm) with my left hand the auger came right off, putting the new one on is very simple.

Replaced water pump. Washer now works as new.
Wife is now happy!

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!

Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!

Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.

went online to replace water pump on washer site and followed directions. Very easy installment.

Take cover off use socket driver to remove two hex head machine screws. There was a foam piece attached to the old part that i pealed off and attached to the new part. It’s there to prevent rattles. There is a tube that pulls out of the old part and a grommet inside that must be removed and placed in the new part. Connect the two electrical plugs and install the new part just like the old part came out.

Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great

I watched a youtube video to see how others performed the repair. My washer was a little different than in the videos but the inlet valve was very easy to access once I pulled the washer out of it's "nook". I took off the back panel of the control "box" (4 screws). Then accessed the valve which was held in place with two screws. The screws were buried behind a few wires so they were a little difficult to access but not impossible. I did need to use my 1/4" box end wrench as my son had borrowed my socket set.

The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.

I downloaded the repair manual on line and followed the instructions for running the diagnostics. This showed that the selector switches were faulty. I then replaced the selector switches following the instructions in the repair manual. Couldn't have been easier.

easiest repair I have ever made. No problems and was surprised as to how fast and easy it was to repair. I did not need two of steps the instructions stated I had to do. best purchase I have ever made.

Just follow the directions, it's easy. My biggest gripe is with Whirlpool. We moved into this house about a year ago; the dishwasher was new at that time. The house we moved from also had a similar Whirlpool dishwasher, less than a year old. Both had these roller assemblies break. The replacement parts are from Whirlpool, and of much better quality. I don't understand why they don't use the better parts when making the unit.