WCCB1030D0KC General Electric Washer - Instructions

Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

replaces as per video. Very helpful

front back and top have to come off, but contrary to 'youtube' instructions, 'nothing' has to be disconnected, if the washer is pulled away from the wall and power unplugged things can be unscrewed and pushed back enough to pull the inner tub out and get to the seal without disconnecting water lines wires or anything else.. the main shaft nut is aluminum and the shaft is 'castellated' so alittle penetrating oil on it and a short 10" pipe wrench in conjunction with a 2lb sledge busted it loose easy enough so i didnt need to buy a spanner .. the seal was easy to get out with a couple of screwdrivers wedged in the sides .. the old split ring crumbled upon removal also so get one of those .. i lucked out on the washer that goes with it and mine was still usable but if it was rusted any more than it was i wouldve needed that also .. so good idea to get the 3 items if your doing the seal - seal, split ring, and washer - another thing, i cleaned everything up good, knocked everything off with a brass brush, polished the shaft seal area with some 600 grit and then lubed the seal with silicone grease thinking it might be hard to get in .. it wasnt .. and it leaked slightly until i did several loads .. in hindsight it would be better to 'lightly' coat the outer edge of the seal that mates to the tub with a good silicone gasket maker, the inner lips with the grease would be fine ... so thats about how it went, parts came quick and i had it all fixed up in a couple of hours .. cleaning things as i went probably took longer than the wrenching ..

Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.

Replaced pump. New pump same manufacturer and model, but better built; however, base plate not same, requiring that I swap it for the original. Also, pump suction inlet is straight-in, whereas original has 90 degree connection. Disconnect power, and remove old pump. Purchase a 1 1/2" I.D. auto radiator hose, cut off use the 90 degree bend; it's a perfect fit to pump conn.; use a 1" PVC coupling on other end socket to mate to the washer drum convoluted drain hose socket. Throw away the crappy original G.E. hard-to-use spring hose clamps and use stainless steel automotive type gear clamps instead. WARNING: Do not try to bend, stretch, or kink the rubber tub drain hose to fit up to the pump without installing an elbow; the installation geometry must be exactly the same as the factory-designed installation. To finish the job, power up and run the machine through several cycles with the front cover off to check for leaks. You will also see why the rubber drain hose must be reinstalled as described above. This washer does not ramp down speed when in the spin cycle, and when the motor stops, the drum makes a sudden 15 to 30 degree rotation, stretching the drain hose to it's limit. Finally, keep your hands out of the machine when it's running; the motor, belt, and transmission drive can cause some real damage if you get tangled up in them. Pay attention to what you are doing; if you are confused by my little dissertation, hire someone qualified to do the job for you.

Repair was done with the help of step by step insructions available on utube, just enter model# and the repair you need to do. One problem I had was new tub seal{GE part] was a little smaller in diamater than the seal I removed And still leaked when I first ran washer So I took it back out and used a sealer [Permatex Indian Head gasket shellac compound from auto parts store] as recommended by one of the the repair techs on utube and it sealed it perfectly, just let it set op for about three hours and nice and dry now

my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.

This site and buying experience WOWED ME!!! After realizing what happened, I searched how to open up a washer, since I had never done it before. My search brought me to your site, which had an excellent 'how to' video for my exact problem of replacing the pump! I ordered the part, which was delivered to my door in LESS than 24 hours! Unfortunately, there was undrained water in the washing machine so while undoing the clamps on the old pump, the water drained on my kitchen floor, so beware of that issue. Because of the positioning of the pump, the clamps were a little tricky to redo, but completed without too much difficulty. I also had to 'unplug' (with a coat hanger snake)the drain tube connecting the pump to the back of the washing machine so it could flow to the outside drain pipe. This was the best internet buying experience I have ever had! Thank you so much! I fixed a 15 year old washing machine for about $40.00!!! (And I am a 57 year old grandmother ;-) Woohoo!!!

After doing some research on the problem I decided that the rubber tub dampers were probably the problem. Replacing them was simple and straight forward after watching the video. A test spin after installation revealed that the problem still existed. This time I watched the bottom of the tub with a flashlight as the spin cycle began and I discovered that the concrete counter-weight was loose on its platform. General Electric had attached a 5 lb concrete block to the tub support with two self tapping sheet metal screws that had stripped out. I screwed the screws back in and added two nuts to the protruding screw bottom and locked them together. Problem solved. The main difficulty in this repair is reaching to the back of the washing while laying on the floor. And sharp edges on everything.

I watched the YouTube video. Great help. The part was at my house less than 24 hours after I ordered. Great delivery! The repair was a no brainer even for a novice like me.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

Repair went great. The large nut had to be soaked to free it but the part was an exact fit.

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!