GTW465ASN8WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Oxford, GA
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer would not drain
Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GROVE CITY, OH
- Parts Used:
- WH13X26535
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When not in use, water was dripping into the washer
We are on a fixed income so my wife and I did the repair ourselves. Thanks very much to the instructions George from Clarksville, Tn. provided on your website. She read the instructions and I followed them. the repair went excellent, THANK YOU GEORGE. All is well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Columbus, OH
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer would not empty when it hot drain cycle
Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from BOSSIER CITY, LA
- Parts Used:
- WH43X24454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inner part of fabric softener dispenser base broke off
looked up part not exactly easy. that was the hard part. it was delivered next day and just had to pop into place extremely easy instalation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from McKees Rocks, PA
- Parts Used:
- WH01X27538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Washer not spinning enough to get excess water out of clothes
1.)disconnected washer from water & electric (remember to turn water off 1st)
2.)pull washer out and leaned it back against the wall to access bottom of the washer
3.)remove protective cage covering belt assembly with nut driver. (4 screws and one has a ground wire)
4.)remove old belt by turning pulley’s and nudging it off of the flat pulley.
5.)install new belt groove side in. Put belt on grooved pulley 1st and slowly turn pulley’s while nudging it onto flat pulley.
6.)reinstall protective cage (don’t forget ground wire) and set washer right side up.
7.)slide washer back in place, hook up your water then plug in machine. (Remember to turn the water on)
2.)pull washer out and leaned it back against the wall to access bottom of the washer
3.)remove protective cage covering belt assembly with nut driver. (4 screws and one has a ground wire)
4.)remove old belt by turning pulley’s and nudging it off of the flat pulley.
5.)install new belt groove side in. Put belt on grooved pulley 1st and slowly turn pulley’s while nudging it onto flat pulley.
6.)reinstall protective cage (don’t forget ground wire) and set washer right side up.
7.)slide washer back in place, hook up your water then plug in machine. (Remember to turn the water on)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Naples, FL
- Parts Used:
- WH44X24385
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced GE Washer lid
Removed parts from old lid (bumpers, switch component and hinges), removed old lid, then replaced parts on new lid. The new lid fit perfectly and looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Kalispell, MT
- Parts Used:
- WH43X31240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The washer agitator/auger broke off of the base during a wash cycle. The small plastic clips broke off the auger so it couldn't be put back on the base.
The agitator/auger was easy to replace - it just snapped into place. We watched a YouTube to make sure to lock it into the counter clockwise direction.
This saved lots of time and the cost of a repair person to come.
This saved lots of time and the cost of a repair person to come.
Was this instruction helpful to you?
Thank you for voting!