WWSE5240DCWW General Electric Washer - Instructions

First I removed the old part (2 screws)
Pulled off 4 wires (maybe the wrong word, I'm not a professional!
Put the new part in-turned the water on and had a stream of HOT water-yay
I had been putting this off because no one in my family had noticed (except me) and with my husband out of work it seemed like a low priority, but when my daughters came home for Christmas, they said "There's no hot water in the washing machine" so I took the plunge--I cannot believe I waited that long!
It literally took me seven minutes!

When disassembling I could not remove the 1 3/4" tub nut with in house tools and had to order the spanner wrench. Almost mandatory unless you have a socket wrench.

Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

Got on line and hooked up with Parts Select and found thru similar stories that the overflow problem with this GE wash machine was a common problem and was explaned what parts were needed and described how to access the parts inside the control panel.
So I ordered water valve 1155105 and pressure switch 269820. I pulled the plug and turned the water supply off and disconnected the hoses. Pulled the knobs off the front panel and removed 4
screws. I identified the parts and how they were attached. Removed the wires and removed and replaced the parts. Put everything back together and the machine works great!

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

I replaced the old knob with a new one.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Tub seal was found completely broken. Replaced it.
Then replaced tub bearing, tub bearing washer, shaft & mode shifter assembly and 6-rib drive belt.
Reassembled and tried, more quieter and like new machine.

Loosening tub nut was a challenge as it was bit corroded, use of WD40 was a great help.
Knowledge from you tube was a great help.

The first attempt to fix the problem did not turn out so well. I replaced the tub bearing, split ring, tub bearing washer and the hub washer. After reassembly and testing, the loud airplane noise was still present during the spin cycle
Then I ordered and replaced the mode shifter shaft assembly and, since I was going to disassemble again, also ordered a new 6-rib belt. Once reassembled and tested, it was quieter than when it was when brand new, according to my wife.
Parts came in very quickly and the tutorials/youtubes were spot on.

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.