WDSR2080DC General Electric Washer - Instructions

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Turned off the water and disconnected the water lines. Took of the control panal, only 4 screws and got access to the dual inlet water valve. Device removes with 2 screws and power connectors slide off. Reverse removal and your in business. So easy to do, part was an exact fit. Don't buy a new washer, fix your old one!

Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

Popped the lid and activated the lid switch. Agitator danced around but the tub not moving. Agitator was un-snapped so no issue getting it out. Forgot to shut the timer down. By the time I came back with container's for wet laundry the pump emptied the water. Found this web site for parts and liked what I saw on the help. The video was a nice overview but can forget about trying to save the hub nut. The trans shaft has 4 flats on it and years of crud gets drawn into the threads sealing it like it was epoxied in with rust. This one is a 13yr old.
Spent most time reading the help stories and gathering up tools. My concern was getting the bad parts out and that hub nut without more damage. Finally found a 1924 vintage 9" monkey wrench I forgot I had and it fit just fine for putting it back together. I put a 1/8" bit in the drill and put a hole in center of nut next to the flats about 1/8" down by 3 of the flats. Wacked the nut in 2 locations with the chisel in the unwind direction with the corner of the chisel in the hole to put a grove on the nut so to keep away from damaging trans shaft. It finally came off in 3 pieces.
After pulling the basket stuck a rag in the drain hole. The basket sounds like it has water in it but its the counter weight attached on top. Brushed up the crud on trans shaft and sponged out the remaining water and other particles.
Next was a pump inspection. If you take the input line off you can see the impeller to remove any stuff that may damage it. Have to un-bolt the pump be careful on the wiring to pump trying to unplug the wires may damage the connectors or even worse the pump. I mostly had crud in the water on the line.
Ordered the needed parts, and cleaned up the tub, reinstalled the pump. After the parts arrived took about a 1/2 hour to put it in service again. Don't forget to wack the hub nut on tight when installing so it wont come off in use.
Many thanks to all in sharing their story it helped me out to see what to expect.

The worst part of the repair was removing the old hub nut. Don't bother messing with the spanner wrench, unless the washing machine has never been used. Split the nut off with a SHARP cold chisel and a heavy hammer. Be very careful not to damage the threads, because not even GE can or will tell you the die size to re-dress the threads if you damage them. Check drain pump motor to remove debris before using washer. Parts were delivered in a quick and efficient manner.

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

Easy enough. I had some help tightening the hoses to the inlet valve. I watched the video about how to repair and it was straight forward and easy to follow. You'll need a bit of strength to tighten the hoses to the dual water inlet valve. Be precise when lining up the threads of the hose and the inlet valve...don't force it...find it...if it goes on crooked it will strip the threads and wreck it. Recommend purchasing some plumbers tape to wrap on the the threads of the Dual Water Inlet Valve. Fixed the dripping water problem immediately.

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

The repair went just like the video! Easier than I would've hoped.

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Well first I had to remove the control panel and that was nice because there was a diagram of the washer in there. So after that I just removed the top, front panel of the washer and top of the drum. Since the hub was broken all around I was able to remove the drum without removing the big nut or the part of the hub that was still attached to the shaft.
This gave me a little more room to remove the nut and hub. The nut was difficult and tight. I struggled with it for some time and got nowhere. I then realized that the nut was aluminum and so I just heated it up a bit and it came off with little effort. I had to heat up the remaining part of the hub also to get it off.
It doesn’t take much heat to get these parts moving. I used a small torch but a heat gun would be better. Also I painted the new hub to try to slow down the corrosion effect water has on the pot metal. I just used some rattle can engine paint I had.
I then cleaned all the parts and put it all back together and all is good.