WCCB1030F General Electric Washer - Instructions

Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.

The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.

I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

Remove agitator. Pry off with screwdriver. Removed agitator hub with socket wrench. Removed tub retaining nut with a pipe wrench and replaced with a new one. Tighten new retaining nut with a pipe wrench and by hitting with a 2 lb. hammer. After tightening, added 4 tub washers, before replacing agitator hub and tightening hex screw on top. Lined up agitator to hub and snapped down securely.

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.

Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!

First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

Remove front panel by pulling on both sides of it at top.

Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.

Replace hose and re install clamps.

follow youtube vid. simple

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.