WISQ416FTAWW General Electric Washer - Instructions

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

This was an inexpensive part with high probability of needing it, so I ordered it before beginning to take the washer machine apart based on "noisy" symptom. The fabric softener cup pulled straight up easily with no tool. Then, the agitator pulled straight up easily with no tool. The bolt was easy to get to with socket set and the coupler pulled up using 2 small pieces of wood as levers to pull it up evenly and straight. This didn't solve my noise problem, but was an easy and inexpensive fix to try. FYI...when I continued trying to troubleshoot, I took the belt off and the noise stopped, so I think the transmission is my problem. I tried for 2 days with WD-40, then with C-L-R to get the hub nut to move, and couldn't. I then tried to split the nut using a screwdriver and a hammer and it appears to be split in 2 places, but the nut still won't budge. I listed the washer on craigslist today too frustrated with the hub nut to continue the repair job. The cost of a repairman plus the transmission would have been over half of a new washer machine, and I still would have had a 8+ year-old motor, and I ran across a great deal on a scratch and dent model at Sears, so I am replacing the washer instead of repairing it.

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

I lifted the agitator stragiht up. removed agitator coupling bolt w/pliers. went on Partselect.com to order replacement coupling, which supplied me with exploded diagrams, entered part number in box at the bottom of the screen and waited 2 days. It then took me less than 5 minitues to complete.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.

Simple replacement. Very easy.

put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.

Just took the old knob off and put the new knob on. It was a snap. Thanks you very much