WISQ416FTAWW General Electric Washer - Instructions

Took the top cup off the agitator, popped out the agitator by grabbing it with both hands and yanking, unscrewed the nut to the agitator coupling, put the new one on and tightened it up, popped the agitator back on. Works great no problems. Though I did find out that the factory had changed the part sometime ago and it actually did need to be replaced.

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!

pulled off the old knob and replaced it with the new knob.

Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)

take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.

I lifted the agitator stragiht up. removed agitator coupling bolt w/pliers. went on Partselect.com to order replacement coupling, which supplied me with exploded diagrams, entered part number in box at the bottom of the screen and waited 2 days. It then took me less than 5 minitues to complete.

This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!

First, I removed the agitator by reaching in the washing machine and pulling up on the agitator until it popped off. Next, I removed the 1/4" bolt that attached the coupling to the spline. Then I removed the coupling. After removing it, I replaced it with a new one, installed a new bolt, and reattached the agitator. It took 2 days for me to get the part(ordered on a Sun)but only took me 10 minutes to repair.

I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.

Ordered a new knob and replaced the broken one.

First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!

This was an inexpensive part with high probability of needing it, so I ordered it before beginning to take the washer machine apart based on "noisy" symptom. The fabric softener cup pulled straight up easily with no tool. Then, the agitator pulled straight up easily with no tool. The bolt was easy to get to with socket set and the coupler pulled up using 2 small pieces of wood as levers to pull it up evenly and straight. This didn't solve my noise problem, but was an easy and inexpensive fix to try. FYI...when I continued trying to troubleshoot, I took the belt off and the noise stopped, so I think the transmission is my problem. I tried for 2 days with WD-40, then with C-L-R to get the hub nut to move, and couldn't. I then tried to split the nut using a screwdriver and a hammer and it appears to be split in 2 places, but the nut still won't budge. I listed the washer on craigslist today too frustrated with the hub nut to continue the repair job. The cost of a repairman plus the transmission would have been over half of a new washer machine, and I still would have had a 8+ year-old motor, and I ran across a great deal on a scratch and dent model at Sears, so I am replacing the washer instead of repairing it.