WCCD2050FW General Electric Washer - Instructions

Remove top of washer, 2 screws,support washer tub use wood block,s to support washer tub, remove old support rod replace with new, that's it, replace top, done. Thank You

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Turn the washer around and take off top back plate behind the controls. Fold controls forward out of the way. Disconnect electrical connection on triple valve by lifting holding clip slightly and pulling out plug. Remove clamp from hose at valve and pull off hose. Remove two screws and replace valve. Install new valve in reverse order.

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

The Hub nut was very corroded and seized, and would not break loose using several types of wrenches & lubricants. The shaft is square with threads only on the corners, I used an electric drill to crack the hub nut on the straight sides of the shaft where there are no threads. All parts are GE and exact replacements, The noise is much less, but still a very small water leak. Should work for awhile , but a new washer is in the near future. Parts are good with quality service and shipment.

Followed the instructions from internet videos and diagrams provided by GE behind the electric panel. The hub nut and remnants of the broken hub had to be ground off. As with the other repairers, the grinding presented some difficulty. Particular care must be taken not to grind into the shaft or other parts on it. Not having much experience in fixing appliances, it came as a surprise that the washer functioned normally after the job was completed. The effort took an afternoon and spilled into the evening.

Well first I had to remove the control panel and that was nice because there was a diagram of the washer in there. So after that I just removed the top, front panel of the washer and top of the drum. Since the hub was broken all around I was able to remove the drum without removing the big nut or the part of the hub that was still attached to the shaft.
This gave me a little more room to remove the nut and hub. The nut was difficult and tight. I struggled with it for some time and got nowhere. I then realized that the nut was aluminum and so I just heated it up a bit and it came off with little effort. I had to heat up the remaining part of the hub also to get it off.
It doesn’t take much heat to get these parts moving. I used a small torch but a heat gun would be better. Also I painted the new hub to try to slow down the corrosion effect water has on the pot metal. I just used some rattle can engine paint I had.
I then cleaned all the parts and put it all back together and all is good.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

Followed the U-Tube video, but...don't waste your time trying to remove the spanner nut with a wrench. Just cut off with a grinder. Second, the hub was locked solid on the transmission shaft. Ended up cutting that off with a grinder also. Would have same myself a few hours of work and lots of frustration if I just cut them off from the beginning instead of trying to remove per the video. Otherwise, very doable, and not a bad job to do yourself.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Replaced the parts with the highest percentage of noise cause from your website. After replacement and reassembly, with the help from your very helpful instructional youtube and my son's assistance, the repairs did not get rid of the problem. Called and was instructed that it could be the mode shifter shaft assembly. Ordered that, as well as a new belt since I would need to disassemble again. Parts came in the next day. Changed out the new parts and the problem was solved. Since I was now familiar with the repair process, this one only took 1 1/2 hours. Very pleased with the level of service and advise received from your group.