FWSB67RGS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anita from Orange, TX
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
water not turning off
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from St. Louis, MO
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water dripping into the tub when off
Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the control panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Interlaken, NY
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
water would not shut off causing door to pop open and spill all over the floor
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Eagle River, WI
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water would not shut off
Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malcolm from Shelley, ID
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front load washer continued to fill with water until door failed. Major Flood
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Dania Beach, FL
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench set
When the washer was filling up with water it would not stop and overflowed. This only happened once.l I called Frigidaire & was told I needed a new agitator & could replace it myself.
My Son replaced Dual Action Agitator & said it was easy. He did it in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Deshler, NE
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tenant lost knob and landlord replaced it.
Just pushed the knob on to the metal on-off control,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Humberto Aarón from Castroville, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The washer hose assembly had mutiple tears in the bellow section of the hose, towards the outlet net the spout.
Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from burleson, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Unit did not drain
removed and replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Kelseyville, CA
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wouldn't rinse, spin, or pump out the water
Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Oquossoc, ME
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
A Leak In The Water Inlet Valve
It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.
Was this instruction helpful to you?
Thank you for voting!