970L48422E0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diana from THOMPSONVILLE, MI
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer woild not spin out left clothes sopping wet
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from PHOENIX, AZ
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Latch broken. New part installed as per repair video - no problems.
New part installed as per repair video - no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from INDIANAPOLIS, IN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The small plastic piece broke that locked the door.
Screwed the new part back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from hampton, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spin cycle sometimes
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Fruitland, ID
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not complete the spin cycle
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ROY, UT
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken plastic door strike
Easy fix for a verry poor designed door catch. Almost purposeful on the manafactures behalf to make it out of cheap plastic Remove 2 screws replace install 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from Santa Clara, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer drum would not spin
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Saint Augustine, FL
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manny from Old Bridge, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine wouldn't go into final spin.
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LINCOLN, ME
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece of door latch lodged in switch
Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from GUILFORD, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doesn’t close
Remove screws take off striker .Put striker back on with screws back on
Tighten screws. Took 5 minutes
Tighten screws. Took 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica Ramaker from SAINT PAUL, MN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Strike
Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DELTONA, FL
- Parts Used:
- 134618213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
While using washer a E9F code appeared and stopped working.contacted parts select trouble shooting site they told me what it was ordered the part they were right on!back washing again thanks so much for the help!
Did it with no problems at all just followed the video step by step worked great done in 1hour!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer drained withn no spin
Remove top of washer, remove door lock assembly,install new assembly replace top.
Was this instruction helpful to you?
Thank you for voting!