GSWS9719AS1 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helen from Walden, CO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke
Opened package. Removed part from plastic bag. Put part on washer. (Thanks for sending it so fast.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad drive belt
remove old belt, install new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Lake Worth, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked on/off switch knob
Just push the new knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Blue Eye, MO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob had broken
Had already pulled off the broken knob--actually it had fallen off in my hand. Opened the package, pulled out the knob and pushed it onto the knob shaft. Simple. Less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Reston, VA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic shaft fit inside plastic selector knob broke
Slip replacement knob on to selector switch shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cape Canaveral, MI
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob on dryer
We were at our condo in Florida and only had a limited time before we had to leave. After a local search we went the Internet and ordered our part and had it in two days. B Thanks. Bob and Marge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from burleson, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Unit did not drain
removed and replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hamilton, OH
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My washer started making a loud, screeching noise and then stopped working.
Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherry from ellenburg depot, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Calexico, CA
- Parts Used:
- 134418700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from wilmington, IL
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would flood out the floor now and then
One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Millard from Grand Prairie, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Belt Had Smoked
Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.
Was this instruction helpful to you?
Thank you for voting!