LAFW7000LW0 Frigidaire Washer - Instructions

Installed New shock absorbers and new door strike. The existing broken shock absorbers caused the drum to oscillate and pull wires from door lock switch.

During this repair job, I replaced the outer door cover and door hinge of this front loading washer. The outer door cover had cracked and shattered above the top hinge pin, leaving only the lower hinge pin to keep the door mounted onto the washer. The outer door cover contains the door hinge housing. Initially, I could not remove the hinge from the front of the washer, because the attaching flat-head screws were REALLY torqued onto the washer. My hand held screwdriver was unable to loosen these screws, so I bought a Black & Decker cordless 12V impact driver from Home Depot for $59. This power tool worked great, and I removed the hinge assembly and door from the washer. When you're using the impact driver, make sure you've got the correct sized bit for the Phillips head. You can buy a bit set at Home Depot. If you don't use the correct size, you'll just strip the head, and then you'll also have to buy a damaged screw extractor. Once the hinge was removed, I discovered that the lower hinge arm had been bent, due to the door hanging off just the lower arm. When I attempted to straighten out the hinge arm, it broke off. After a few choice words, I ordered a new hinge assembly from PartSelect. Once I received the new hinge, I reassembled the door, and attached the hinge to the washer. When seating the plastic hinge bushings into the outer door hinge housing, make sure the slotted tabs of both hinge bushings are fitted snugly into the hinge housing. You won’t be able to reassemble the inner and outer door covers if the bushings are not seated properly, I finally got everything back together, and now my washer works great. Using perfect hindsight, I would also recommend that my fellow handymen replace the proprietary flat-head screws which hold the hinge onto the washer. My first attempts to remove the hinge screws damaged them pretty badly. You should also consider replacing all the screws which hold the inner and outer door panels together.

I replaced doorlok as every one sujested but that did not fix it I then replaced thr control panel with a new upgraded one. It is not that simple for an amature. New control came with one of the control shafts missing had difficulty getting it in position so so control would be on right function. after all that I found diagnostic instructions taped to bottom of washer

Watched your supplied video on how to repair. I did not want to break the washer door sealas described on the video. I removed the two screw on the back of washer that held the top and then slid the top off. I moved the two screws securing the switch at the exterior door. I changed the door lock and switch assembly through the top by moving the connectors one at a time from the old assembly to the new. Replaced the screws to complete. I then changed the door strike by removing the two screws and replacing the new strike. Job complete and washer works fine saving us $200.00. Thank you ever so much PartSelect.com.

It went easy

The entire process, from diagnosing the problem, ordering the part, and instalation was fantastic! I ordered the part Friday afternoon and had it at my door Saturday afternoon. I was so relieved to read the installation posts from other customers demonstrating how common this issue is and how easy it was to fix! I simply watched the installation video that was sent with my confirmation email. It is also conveniently located on your website. I had the new part installed in less than 30 minutes AND before my husband got home! Thank you Partselect.com!

Remove the 2 screws on the rear of the top panel. Open door and remove the 2 screws holding the latch assembly. Reach down and pull up latch. Remove the 3 wire connectors. Plug wire into new latch and re-install in reverse order.

Removed the door lock and switch assembly. With needle nose pliers, I removed the metal ring around the washer gasket. Removed two screws on assembly and removed the entire assembly. Noted part number and ordered part which came in 3 days. Reversed the above instuctions for removing the assembly. Was washing within the hour. By the way, I am a 65 year old woman.

took the top off removed the old one and put in the new one.Works great!!

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.

I am a 64 year old female that had never attempted to fix anything. This was my 1st attempt at fixing something. It took longer to look for phillips screwdriver than it took took to repair it. Thank you so much for instructions.

Simple removed the screws from the door, did this the night I broke the glass. Gently pryed the inside of the door apart from the front of the door panel. Lined up the arrows on the edge of the new glass panel with the inside of the front door panel and placed the inside plastic door panel back on, to hold the glass panel in place. Replaced screws. Everything worked great! Easy, affordable fix!!

The end of the door strike had broken off in the lock. The door strike itself went on in just a few minutes. The time consuming part was getting the piece that had broken off out. After trying with tweezers to get it out, we took the lock off the machine and finally got it out. So....if the door strike looks damaged or isn't shutting properly, replace it before it breaks off inside the lock. We were pleased with how quickly it came. We ordered it Sunday evening and it came Tuesday morning.

with a code it gave me i was able to determeine it was the door lock switch it was so easy it was unbelievable

Everything went great, except replacing the rubber seal, that was a little bit harder to put back in place. But other then that, went very well and easy to repair.