FTF2140FE1 Frigidaire Washer - Instructions

Replaced drain pump using this walk through. Different models, but pretty straight forward.

The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.

The video was most helpful, and the left shock replacement went as shown. The sucker punch was getting to the right shock - much harder.
First notice video has washer on a stand. How nice to have had it up on a table. LOL As it was I tilted the machine back with a 6 inch block under the front. Still a bear to get to the shock, but w/ patience, doable even though you are flat out on the floor.
The old shocks were so bad that the pistons fell out once it was removed.
It takes some strength to get the pins through the new shocks, and as I have a weak left hand I had to resort to using a C-clamp to help. If I could have gotten my right hand in there I may not have needed it. Right hand did have to hold the clamp as it had to just catch the side of the pin hole since the pin is pointed and sticks out past the mounting bracket when seated.
I also ordered a spring but they both were still good.

After locating the two screws on the inside of the door, I used a phillips screw driver, in a counter-clockwise motion, to take the screws out. I then removed the remaining pieces of the broken handle and then positioned the new handle in the holes seating it firmly in place. The handle had to be held into place while I negotiated the screws back into the holes turning the screws in a clockwise manner.

love parts select have used them several times for parts great company

One new door handle two screws and 5 minutes later it was like new again. Saved a bundle by doing the repair myself.

removed the old handle held in by two screws lined up the new handle and reinstalled screws

unscrewed old part. screwed on new part. it was a breeze.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

(actually my husband did this) Took out the screws left in the broken door handle, inserted into new handle and tightened. It works perfect.

I just pushed the washer on its side on a price of wood. I put a pan to catch the drain water.It was then as easy as detaching two boots and two bolts that hold the drain motor on.Do it in reverse and you got it.Oh first don't forget to unplug the electrical wires ect.

Pulled the locking pins out, replaced the shock absorbers and re-installed the locking pins. I used Channel Lock pliers to remove and replace the locking pins. i used a deep socket to hold down the tab on the locking pins so they could be pushed out. The new shock absorbers came with installation instructions.