FTF2140FE1 Frigidaire Washer - Instructions

I started with a Phillips head Screw driver and removed the screws from the current Door strike and replaced with a new one. To replace the Door Lock and switch assembly I had to access the right portion of the door gasket which was a little tricky, as it has a wire ring around the gasket to keep it in position. It has never been removed so it was fairly stuck so I took some pliers to pull on the gasket and ring to loosen it up. Once I got it off I was able to remove the Gasket just enough to access the electrical components to the Switch assembly. I loosened the screws on the current switch assembly using a Phillips head screw driver and removed it through the access point then unplugged the current wiring harness from the switch assembly and plugged the new switch assembly in. Then I tightened up the screws on the new switch assembly. re attaching the gasket was possibly the most time consuming as there is a metal lip on the door itself that the gasket has to wrap around in order to re attach the metal ring and hold everything in place. I took a flat head screw driver and ran it along the edges of the metal lip while pulling the gasket to secure it around the lip then I wrapped the metal around the gasket to secure it to the metal lip in the door ( Note: the metal ring has a spring that should be positioned at the bottom of the door once it's installed correctly, you will notice the gasket is shaped at the bottom to allow for the spring) Once I completed that I made sure all screws where tightened and then checked the unit to be sure it worked properly. It is working perfectly and no more error message.

It was very easy. I simply unscrewed the 2 screws set the new latch into place and replaced the screws.

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

Unscrewed the old striker and screwed in the new one.

There were only two screws that held the door strike/catch in place. I had to fish out the broken plastic piece with a pair of hemostats. The only difficult part about changing the new piece was that I had to find someone with the correct screwdriver to use since it was not a standara screwdriver. Luckily I live next door to a mechanic and borrowed his. The two screws came off easilty and I was able to replace it in 2 minutes. I was thrilled that the part that I ordered arrived the next day.

With the help of PartSelect's diagnosting tool it was easy to find the right part. The part arrived very fast and the installation was "child's play" by following PartSelect's video. I must have saved > $100. Thank You very much. -Anna-

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Removed and replaced two screws.

Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!

Watched the video on website and followed what they said. Worked great.

I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.

the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.

pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...

Removed screws and screwed in new handle.

It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!