GSWS9471DC0 Frigidaire Washer - Instructions

This is complicated repair. It requires removing the dryer unit to get access to the water valve. The repair requires 2 people. One to help stabilize the dryer in the removal process and also to hold the dryer on top of the washer once it has been taken loose. The other person does the actual repair. None of the online techs had a clue on how to do this repair. So this was a learn as you go event. First completely disconnect the unit and move it so you have access clear around the unit, as you will need to be able to get on all 4 sides. Now as you face the unit remove the angled cover panel between the dryer and washer. Behind the cover panel is another panel for rigidity, remove it. Slide your hand down the inside of dryer cover panel on the left side. This will also require a flashlight to see what you're doing. Find the 3 hex headed screws that hold the left side on on the washer. DONOT CONFUSE THESE WITH THE SCREWS ON THE OUTSIDE THAT ARE EASY TO GET TO!! There is one at the rear, then one at the center, and one right up against the edge of the front. The one at the front is almost impossible to get at. Remove the front one FIRST. ALSO LOCATE THE 2 EXTRA HOLES BY THE FRONT SCREW BEFORE YOU REMOVE THE SCREW. Cause when you get ready for the reinstall those 2 holes are an issue. If you wait to remove the front last, the dryer unit is no longer stable and it will BITE you. Now go to the right side and repeat the process. Make sure your helper has a good grip on the dryer! Remove the 2 external screws at the rear where they hold the L bracket on, one on each side. Now the 2 of you pick up the dryer and sit it on the washer. There is just enough slack in the lines, wires to accomplish this without having to disconnect any of them. Replace the water valve, this part is a no brainer. Now for the reassembly. Sit dryer back in its proper place on the washer, have your helper hold it securely. Line up the holes. Install BUT DONOT TIGHTEN the rear and center screw on each side. Now attempt to install the front screws. Make sure you get them in their correct holes, the 2 spare holes are not threaded and larger all they do is grab your screw and make you fight to get it back, which can be done. Attach the 2 external screws on the rear. Tighten all the screws now. Reinstall the structure panel on the front, and then the cover panel. Hook up unit and you're done

followed on line instructons very easy

before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.

Replaced Water inlet Valve. Did not solve problem. Rapidly cycled switch between Small and Super Size load and water began filling.

Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.

watched the video, all instructions were perfect!

removed and replaced pump

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

The repair was very simple. Just remove the fabric softener container at the top of the agitator and there was a cover with a little plastic "hook" on the top. Just take a pair of pliers and pull on the hook pretty hard and it pops off. Then using a 1/2" socket, loosen and remove the bolt and pull off the old agitator. Slide the new agitator over the "drive shaft" where the old one was, tighten the nut, put the cap back on, place the fabric softener tray back on, and I was back in business. Works great now.

undo hose (both) lift top remove screw ,tub hose,elect.connectors lift valve out,put in new in reverse order///

My wife done the repair while I was out of town. She never tries to won't on anything in fear that she will mess it up.But she said she had it fixed in ten minutes. Just take the hoses off the pump, unplug, and unbolt where mounted. Then reverse to put on new one. Partselect is always very prompt to sent my parts and I have never had an issue with anything. I will buy all my parts from them from now on.