FWSB7800DS0 Frigidaire Washer - Instructions

replaced it with the new one

followed on line instructons very easy

removed two screw at the bottom of front panel and pulled down on panel to remove, determined water coming out splash seal, splash cover held on with plastic clips around cover. Removed two screws on back side of top and hinged top over removed splash cover and cleaned old seal out replaced with new seal.Simple job but could not find parts locally and found Partselect on internet and ordered parts, very friendly and knowledgible person, ordered parts and had them in three days, would very highly recommend. Thank You Joe Lumpkin

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!

Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.

This is complicated repair. It requires removing the dryer unit to get access to the water valve. The repair requires 2 people. One to help stabilize the dryer in the removal process and also to hold the dryer on top of the washer once it has been taken loose. The other person does the actual repair. None of the online techs had a clue on how to do this repair. So this was a learn as you go event. First completely disconnect the unit and move it so you have access clear around the unit, as you will need to be able to get on all 4 sides. Now as you face the unit remove the angled cover panel between the dryer and washer. Behind the cover panel is another panel for rigidity, remove it. Slide your hand down the inside of dryer cover panel on the left side. This will also require a flashlight to see what you're doing. Find the 3 hex headed screws that hold the left side on on the washer. DONOT CONFUSE THESE WITH THE SCREWS ON THE OUTSIDE THAT ARE EASY TO GET TO!! There is one at the rear, then one at the center, and one right up against the edge of the front. The one at the front is almost impossible to get at. Remove the front one FIRST. ALSO LOCATE THE 2 EXTRA HOLES BY THE FRONT SCREW BEFORE YOU REMOVE THE SCREW. Cause when you get ready for the reinstall those 2 holes are an issue. If you wait to remove the front last, the dryer unit is no longer stable and it will BITE you. Now go to the right side and repeat the process. Make sure your helper has a good grip on the dryer! Remove the 2 external screws at the rear where they hold the L bracket on, one on each side. Now the 2 of you pick up the dryer and sit it on the washer. There is just enough slack in the lines, wires to accomplish this without having to disconnect any of them. Replace the water valve, this part is a no brainer. Now for the reassembly. Sit dryer back in its proper place on the washer, have your helper hold it securely. Line up the holes. Install BUT DONOT TIGHTEN the rear and center screw on each side. Now attempt to install the front screws. Make sure you get them in their correct holes, the 2 spare holes are not threaded and larger all they do is grab your screw and make you fight to get it back, which can be done. Attach the 2 external screws on the rear. Tighten all the screws now. Reinstall the structure panel on the front, and then the cover panel. Hook up unit and you're done

Remove the agitator and the 2 bolts that clamp the spin drum to the shaft and pull up on drum the 2 seals are on the shaft right there. Pry up on the seals to remove them. Install all seals and Be sure to completely clean all parts before putting them back in the machine and re assemble the machine. The bad part of this job is if you have used powdered soap it took 3 hours to clean the parts before reassembly.

lifed the lid .remove oud hose and replaced with new hose

Old part cracked

Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.

sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.