GLWS1439FC1 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- loudvik from glendale, CA
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the pump had died
First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Evansville, IN
- Parts Used:
- 134159500
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Motor fried after being submerged in water...
I pulled the old motor out of the bottom of the washer. After undoing the screws and taking off the belt. I threw the new one in and tightened everything up and put the belt back on and it worked great... Super easy to change a motor out and a lot cheaper than buying a new waher...
The best part was that it only took one day to ship to my house and I picked the cheapest shipping amount... I recommend this site..
The best part was that it only took one day to ship to my house and I picked the cheapest shipping amount... I recommend this site..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Boxford, MA
- Parts Used:
- 134511600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer belt broke
followed the instructions on a blog
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Siobhain from Ashland, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washing machine wouldn't drain
i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Fort Worth, TX
- Parts Used:
- 5303279394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Tub was leeking
Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Trevor, WI
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
CLothes weren't getting dry enough for the dryer.. also made a squeling, rubbing noise while aggitating. Had a repair man for my dishwasher..told him I thought it was the transmission.. he hand turned the aggitator and said that was the problem.. Just needed a new aggitator....whew what a relief!
I'm a 70 year old widow.. ordered the part which came in 2 days..(.very reasonably priced) My son came over and in no time had the old out and new in...works like a new machine... Thank you Part Select. A few months ago ordered a stove ignitor..it too came really fast... stove is good for another 15 years..LOL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clay from Kansas City, MO
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wash tub would not drain/burning rubber smell
I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VALERIE from TUPPER LAKE, NY
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
agitator was stripped, so it kept slipping.
removed old agitator by loosing a bolt at top, after removing the detergent dispenser. agitator came off easily, new one on, bolt on with rachet wrench, dispencer on. works like new. thanks for the great service. the part came in faster than i thought it would, and i would have had to travel for miles to get a part around here. VAL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEITH from BEND, OR
- Parts Used:
- 137221600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Spin Cycle wouldn't work
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Baytown, TX
- Parts Used:
- 134890600
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
water continually leaking into tub when not in use
Repair was harder than originally anticipated. Front had to be taken off, but trying to get all panels back in place was quite a job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damon from Hinesville, GA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer went into spin mode but would not spin
I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Willcox, AZ
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator making clunking niose
Removed the top of agitato removed bolt, R&R part ,put bolt an top back 3min. Top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Huntersville, NC
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer wouldn't spin
I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Asheboro, NC
- Parts Used:
- 134548800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The front level screw legs are made of plastic and each time I move they break
screwed in the new legs and leveled it off again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dixie from STRANG, OK
- Parts Used:
- 131494800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Leaking hoses
I made my job difficult by removing the back panel, then the side, and finally discovered the front panel opens giving access to the washer. Using heavy pliers I removed the spring clamps and replaced the pump to washer hose and the other hose end to the tub. Turned on the washer no leak only to discover the drain hose had developed a leak. So I ordered the second hose. I was not sure how to release the plastic retaining clamps. Finally just yanked them loose, which worked. Ran the hose through the machine out the back into the drain pipe. I was able to reattach the retaining clamps put the spring clamp on the pump end of the hose. The difficult part was getting the back, sides and front of the washing machine together that took hours.
Was this instruction helpful to you?
Thank you for voting!