MWS939AQ0 Frigidaire Washer - Instructions

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

on front of machine,,,removed 2 screws at bottom corners. open top cover, using putty knife to release spring clips between front panel & top cover, lift & support top cover.note; tape hinged lid of machine to hold closed.the remove front panel of washer using a downward motion.re move spring clamp on water pump ,w/pliers, by sliding clamp upwards along drain hose. with a twisting motion,remove hose from pump.thread old hose out through back of machine.reverse reassembly,using new drain hose.note; suggest using an automotive radiator hose clamp on pump/hose connection instead of spring clamp.most spring type clamps will lose their tension with repeated plier action.

I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

The repair was very simple. Just remove the fabric softener container at the top of the agitator and there was a cover with a little plastic "hook" on the top. Just take a pair of pliers and pull on the hook pretty hard and it pops off. Then using a 1/2" socket, loosen and remove the bolt and pull off the old agitator. Slide the new agitator over the "drive shaft" where the old one was, tighten the nut, put the cap back on, place the fabric softener tray back on, and I was back in business. Works great now.

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.

It was easy. No problem getting the to v-belt.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!

I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.

removed two screw at the bottom of front panel and pulled down on panel to remove, determined water coming out splash seal, splash cover held on with plastic clips around cover. Removed two screws on back side of top and hinged top over removed splash cover and cleaned old seal out replaced with new seal.Simple job but could not find parts locally and found Partselect on internet and ordered parts, very friendly and knowledgible person, ordered parts and had them in three days, would very highly recommend. Thank You Joe Lumpkin

Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.