GMWS1339CS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joanne from Lake Worth, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked on/off switch knob
Just push the new knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Blue Eye, MO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob had broken
Had already pulled off the broken knob--actually it had fallen off in my hand. Opened the package, pulled out the knob and pushed it onto the knob shaft. Simple. Less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Reston, VA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic shaft fit inside plastic selector knob broke
Slip replacement knob on to selector switch shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cape Canaveral, MI
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob on dryer
We were at our condo in Florida and only had a limited time before we had to leave. After a local search we went the Internet and ordered our part and had it in two days. B Thanks. Bob and Marge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hamilton, OH
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My washer started making a loud, screeching noise and then stopped working.
Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad drive belt
remove old belt, install new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from Ripley, WV
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer won't drain
My wife done the repair while I was out of town. She never tries to won't on anything in fear that she will mess it up.But she said she had it fixed in ten minutes. Just take the hoses off the pump, unplug, and unbolt where mounted. Then reverse to put on new one. Partselect is always very prompt to sent my parts and I have never had an issue with anything. I will buy all my parts from them from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Walden, CO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke
Opened package. Removed part from plastic bag. Put part on washer. (Thanks for sending it so fast.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Willcox, AZ
- Parts Used:
- 134211400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cold water valve had small wire in it wouldnt close
undo hose (both) lift top remove screw ,tub hose,elect.connectors lift valve out,put in new in reverse order///
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanche from Mansfield, PA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two knobs were cracked and I had already replaced one or two of them before. They seem to crack very easily.
Just pulled the broken knobs off and pushed the new ones on. Very easy!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Fort Washington, MD
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old knobs were stripped and would not turn.
We decided to see if this was the problem so we ordered replacement knobs, and IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Visalia, CA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken selector knob
pulled off broken knob and metal sleeve, replaced with new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from LOUISVILLE, KY
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob stripped and could not turn dryer on
replacement knob replaced old one perfectly,just pressed on where old one fell off,beats looking at a pair of needle nosed vice grips left on the dryer to turn stub where knob had fallen off,wife happy, Happy wife,Happy life.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Randolph, ME
- Parts Used:
- 131862900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
bad rumble when running
released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.
Was this instruction helpful to you?
Thank you for voting!