FWS6600ES1 Frigidaire Washer - Instructions

Old part cracked

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

on front of machine,,,removed 2 screws at bottom corners. open top cover, using putty knife to release spring clips between front panel & top cover, lift & support top cover.note; tape hinged lid of machine to hold closed.the remove front panel of washer using a downward motion.re move spring clamp on water pump ,w/pliers, by sliding clamp upwards along drain hose. with a twisting motion,remove hose from pump.thread old hose out through back of machine.reverse reassembly,using new drain hose.note; suggest using an automotive radiator hose clamp on pump/hose connection instead of spring clamp.most spring type clamps will lose their tension with repeated plier action.

lifed the lid .remove oud hose and replaced with new hose

watched the video on website, printed instructions for feedback.

sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

Good

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.

Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.

The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.