GLWS1939AS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helen from Walden, CO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke
Opened package. Removed part from plastic bag. Put part on washer. (Thanks for sending it so fast.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad drive belt
remove old belt, install new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Lake Worth, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked on/off switch knob
Just push the new knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Blue Eye, MO
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob had broken
Had already pulled off the broken knob--actually it had fallen off in my hand. Opened the package, pulled out the knob and pushed it onto the knob shaft. Simple. Less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Reston, VA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic shaft fit inside plastic selector knob broke
Slip replacement knob on to selector switch shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cape Canaveral, MI
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob on dryer
We were at our condo in Florida and only had a limited time before we had to leave. After a local search we went the Internet and ordered our part and had it in two days. B Thanks. Bob and Marge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from burleson, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Unit did not drain
removed and replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hamilton, OH
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My washer started making a loud, screeching noise and then stopped working.
Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sammy from Notasulga, AL
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not Draing Water
Good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert J. from Homosassa, FL
- Parts Used:
- 134101800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I had no problem
I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Austin, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy spin cycle
Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Trinidad, CO
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burning smell from wash, needed new drive V belt
watched the video on website, printed instructions for feedback.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard from upper sandusky, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer failed to drain
sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!
Was this instruction helpful to you?
Thank you for voting!