Models > GLWS1439FC0 > Instructions

GLWS1439FC0 Frigidaire Washer - Instructions

Jump to:

All Instructions for the GLWS1439FC0

Customer:: Kenneth from Port Monmouth, NJ
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Belt stretched out

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

Was this instruction helpful to you?

Customer:: frank from fostoria, OH
Parts Used:: 137221600
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Wouldn't drain completely and wouldn't final spin

before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.

Was this instruction helpful to you?

Customer:: William H. from Warsaw, OH
Parts Used:: 134101800
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

The washer lid lock was burned

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.

Was this instruction helpful to you?

Customer:: Richard from Lafayette, LA
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Washer would not spin

watched the video, all instructions were perfect!

Was this instruction helpful to you?

Customer:: Daniel from Daingerfield, TX
Parts Used:: 134211701
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

hose leaking

lifed the lid .remove oud hose and replaced with new hose

Was this instruction helpful to you?

Customer:: Gerard from upper sandusky, OH
Parts Used:: 137221600
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

washer failed to drain

sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

Was this instruction helpful to you?

Customer:: Albert J. from Homosassa, FL
Parts Used:: 134101800
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

I had no problem

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

Was this instruction helpful to you?

Customer:: sherry from ellenburg depot, NY
Parts Used:: 137221600
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The water would not drain or spin out all the way

Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.

Was this instruction helpful to you?

Customer:: Elaine from Dania Beach, FL
Parts Used:: 131605901
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Wrench set

When the washer was filling up with water it would not stop and overflowed. This only happened once.l I called Frigidaire & was told I needed a new agitator & could replace it myself.

My Son replaced Dual Action Agitator & said it was easy. He did it in 15 minutes.

Was this instruction helpful to you?

Customer:: Barry from Mohrsville, PA
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

20 year old v belt finally gave up the ship

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Was this instruction helpful to you?

Customer:: Millard from Grand Prairie, TX
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Belt Had Smoked

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

Was this instruction helpful to you?

Customer:: Joseph from Trinidad, CO
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

burning smell from wash, needed new drive V belt

watched the video on website, printed instructions for feedback.

Was this instruction helpful to you?

Customer:: William F. from Poughkeepsie, NY
Parts Used:: 134592700
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

drain hose was leaking

on front of machine,,,removed 2 screws at bottom corners. open top cover, using putty knife to release spring clips between front panel & top cover, lift & support top cover.note; tape hinged lid of machine to hold closed.the remove front panel of washer using a downward motion.re move spring clamp on water pump ,w/pliers, by sliding clamp upwards along drain hose. with a twisting motion,remove hose from pump.thread old hose out through back of machine.reverse reassembly,using new drain hose.note; suggest using an automotive radiator hose clamp on pump/hose connection instead of spring clamp.most spring type clamps will lose their tension with repeated plier action.

Was this instruction helpful to you?

Customer:: Herbert from Randolph, ME
Parts Used:: 131862900
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench set

bad rumble when running

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

Was this instruction helpful to you?

Customer:: Cecilia from Moreno Valley, CA
Parts Used:: 134511600
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Stopped spinning made noise

Changed the belt started working like new.

Was this instruction helpful to you?

All Instructions for the GLWS1439FC0