This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
This gray metal door strike is designed for use in select washing machines, where it plays a critical role in activating the door switch and ensuring the door remains securely locked during operation....
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
If your front-load washer is leaking or making strange noises, the door boot seal might be the culprit. This soft rubber ring fits around the door and keeps water inside while your machine runs. It al...
This washer tub-to-pump hose, often called a coin trap or bellows hose, carries water from the outer tub to the drain pump during drain and spin cycles. Designed with an integrated trap, it captures c...
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
This door lock and switch assembly is a genuine OEM replacement for front-loading washing machines, designed to keep the door securely locked during operation and prevent leaks. It sends an electrical...
This outer door window, also referred to as a door lens, is a glass component designed for use in front-loading laundry appliances, including both washers and dryers. It serves as a protective barrier...
On Order
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tryson
February 8, 2023
Codee42
For model number EWFLW65HIW0
Hello Tryson, thank you for the question. The error code E42 in your washer shows that the washer door is open or not closed correctly, the washer is overloaded or the door lock is faulty. For resolving this issue, we would recommend checking if the door is properly closed, whether any laundry is caught between the door seal and door glass, whether the washer is not overloaded, and disabling the child safety lock using a coin or similar object and trying again. The following parts also need to be checked to fix the issue: the door strike, part number FIX2345126, and the door hinge, part number FIX2345153. Good luck with this repair!
Removed old drawer and replaced it with new one. This is the second drawer assembly I have purchased in 6 months. This piece of junk must be a cash cow for Electrolux. If they would make the small latch out of metal instead of plastic, there would be no problem. But that might cost an additional $ .007 per washer. On the positive side, pa
... Read morertselect.com had the part and delivered it promptly.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfec
... Read moretly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predi
... Read morected that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
