CAWS522TQ0 Crosley Washer - Instructions

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

First, I wrestled off the top cap of the agitator. Then, I unscrewed the bolt and took out the cam. I noticed that the agitator dogs were worn smooth. I replaced them, put it all back together and VOILA! I bought the whole agitator kit, not knowing what I was going to find, because I wasn't a Magtag repair woman. It ended up that the cam that came in the kit was too big for my washer anyway. Luckily, all I needed was 4 plastic dogs. The price of the whole kit was so inexpensive anyway, it was no big deal. Especially because, I was looking to buy a new washer or a big repair bill. This website is great! Thank you.

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

Unplugged the main power. Removed the 2 screws in the back and top of the control panel. Pulled control panel forward and tipped towards me to remove from top of washer. Removed the ground wire screw with a socket/ratchet. Removed the switch by pressing the tap inwards. The tab was brittle and broke. Replaced the switch, ground wire with screw and the control panel. I notice that the 2 screws which secure the switch lever/hinge to the lid were loose. These 2 loose screws were actually the problem in the first place. The loose lever was not making good contact with the switch. I think the switch was actually fine but since I broke the tab on the switch I needed to replace it anyhow. Plugged in power cord and washed a load.

!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.

Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft on the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil

I followed instructions provided from Parts Select for removing and replacing the coupler assembly, and also instructions for changing the clutch assembly. I also took it's transmission apart (socket set and flat screwdriver required), drained the old oil, cleaned it, added new 90W gear oil. The instructions covered the swapping of parts very well. Cleaning up the oil spill took as long as changing the parts.

First unplug the washing machine.
Then used a putty knife pushed under the endcap area to release the clips holding the top console down, then lifted the front of the console and tipped it back. Held it in that position with a short piece of wood.

The lid switch was visible right there on the left. Then unplugged the switch, removed the metal screw holding the ground wire, pressed the locking tab on the switch, lifted the washer lid about 3 or 4 inches, and removed the switch. Installation was the reverse procedure. Total time about 10 to 15 minutes.

We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.

The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.