CFW7700LW0 Crosley Washer - Instructions

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!

Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.

First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.

1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.

Removed 2 screws , unplugged the old switch , replaced with new one and secured with screws . Easy !!

I unscrewed the two screws and replaced with new door striker and used the same two screws I took out. It took me seriously less than 2 minutes and I am a woman!

unscrewed (2) screws, took broken piece off and screwed new piece on with the (2) screws. Keep your old screws because part does not come with screws.

I took off the broken part with a screw driver. I easily found the needed part on your website. After I ordered the part, it came within 2 days. It was the correct part and was replaced within 10 minutes of opening the package. Thanks for the great, easy and quick service!

I found this wonderful web site, after removing the cover and running a diagnostic to find it was either the door lock or the TCP control board. Control board unable to find any information on was scared to call the repair man as they usually cost about $500.00. I am a single mother and order the door lock and just like that I was able to repair it myself. Thanks you so much!!!

took the 2 screws out, removed the old and screwed in the new.Piece of cake. What stod out in the process was Part selects follow up with email and video of how to replace. They are great....

two screws took off the old plate, replaced the door strike with saame screws

I order the part from this website. I want sent to me in 1.5 days. I removed the srews form the broken latch on the door. I place the new latch on the door, than use a phillip head screw driver and attach the latch to the door.

Followed your instruction,simply removed the top cover and the two screws on the door to remove the switch assembly. Unplug old part and replaced with the new one after pluging three wires. I saved $105.00, which was the quote from a repair shop. Thank You for your great service and directions; the part arrived a day after I had ordered, did not pay extra for special delivery.

removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys

The door assembly did not fix the problem this time, it was the control panel that had to be replaced. I have replaced the door assembly in the past, and I am glad I have a spare on hand. They do go out over time from the pressure of large batches of clothes. I am "no repair man", but having someone come out to replace it for you is a $300.00 job, easily. Read the tech info for your error code and go from there.