CAH4205AWW Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brenda from EL Paso, TX
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Torn and moldy boot seal
We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.
We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.
We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from KANSAS CITY, MO
- Parts Used:
- WP22003834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water valve leaking
Replaced valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SAINT CHARLES, IL
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Tight fit
Working from back of machine, slip old belt off drum pulley. Loosen 1/2" nut to remove drive motor from outer drum assembly. Work motor toward front of machine, while holding carefully, to slip out of old isolators. Remove worn isolators. Replace with new isolators (lip towards front of machine). Re-install motor with the nut/washer all the way up against the stop for the least amount of pressure possible on belt tension..tighten bolt. (Believe me.. when you try to install the belt, it will still seem like the belt is not the right size and way too tight.).. It is, however, the correct belt.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from N LAS VEGAS, NV
- Parts Used:
- WP25001052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Thought pump was the problem making noise but the noise is still there might try changing belt and motor isolator hit ,the noise is like a growling noise before pump starts to drain
Followed a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from N LAS VEGAS, NV
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Noisy
The motor isolators went in with no problem ,but the drive belt went on very tight , your how to video shows how. Easy the belt went on , when I called your store I was told that is the only size belt for the machine model mah5500bww,
Thank you Bill
Thank you Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from GROTON, MA
- Parts Used:
- WP25001052
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was not fully draining
Pretty straight forward. After disconnecting the power. Remove the back panel, locate the drain pump. Disconnect the hoses [some water will still be in the hoses, have towels and dry vac ready] Remove protective plastic from the top of the pump and remove the electrical connection reassembled with new drain pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FOLSOM, CA
- Parts Used:
- 12001788
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burn smell during spin cycle.
I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from PORTAGE, WI
- Parts Used:
- WP22003834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hot Water Inlet Valve Stuck open!
After watching the repair video, The job became very easy. Thank you parts select, the only thing i didn't like, was the shipping cost. thought it was a little high for such a small and light part..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CHINA, ME
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
sharp metal edges
after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that
Was this instruction helpful to you?
Thank you for voting!
Loud noise
Beat on spline shaft until I gave up and trashed the washer. Bought new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from McQueeney, TX
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser Bezel plastic cracked at screws
The repair was only 4 screws.
THE AMAZING STORY WAS I ORDERED THIS PART ON MONDAY AND RECEIVED IT ON WEDNESDAY!!!!!!
THE AMAZING STORY WAS I ORDERED THIS PART ON MONDAY AND RECEIVED IT ON WEDNESDAY!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Haddam, CT
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace billows on washmachine
Unscrew door hinges, front panel, soap tray, lift top to 12 oclock position,unhook strap from spring located on top of the drum,tape strap ends to drum to prevent from falling,disconnect the billows drain clamp on the bottom of the billows,remove the billows by peeling off the drum, install the new billows from the top first and tape it to the drum to prevent it from slipping off as you work your way around the drum,install the strap in its track, secure with spring(better with two people)in same location, hook up billow drain, finish doing the laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENNIE from FT WALTON BCH, FL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door shroud had cracks and was leaking water
Removed and replaced old shroud with new one. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Burleson, TX
- Parts Used:
- 22004481
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dispenser lid plastic around metal pins that insert into washer broke so it fell off everytime I opened to add soap etc
I got the part, but it did not come with the pins needed to insert into slot in washer. I had to go to Lowes and buy some pins and improvise to make them fit on both ends. It is working well....Probably saved myself $100.00 (service call etc) Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia E. from Roselle, NJ
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flanges on the bezel had broken (poor design).
Removed old screws and bezel.
replaced new bezel and screws.
The exoloded views and drawings were a great help.. Thanks for being there with views and the right parts that fit perfectly.. Love the service.. Patty O'
replaced new bezel and screws.
The exoloded views and drawings were a great help.. Thanks for being there with views and the right parts that fit perfectly.. Love the service.. Patty O'
Was this instruction helpful to you?
Thank you for voting!