FA6191 Amana Washer - Instructions

Change the position of electrical connection on inlet valve before installation to match positions of old valve. Shut off electricy and water to washer. Disconnected water hoses, and power wires to old valve. Removed old valve and installed new valve exactly as installed on old valve. Washer operated perfectively

Removed 2 screws on the bottom of the front of the washer and pried the front off. Then removed 2 more screws for the top of washer and rocked it back to expose the water inlet vavle. Removed the water inlvet vavle and replaced it. Then put it all back together. Done

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

Followed web instructions.

I first shut off the cold and hot water hoses so that no water would run while replacing the part. After that I made sure to unplug the washer .Then I removed the plate that was holding the water inlet valve with a 1/2 " nut driver ,I think there were four bolts .Then I removed two more bolts from the center of the plate that were holding the water inlet valve.I then disconnected one 1/4 " screw or I should say loosened one which held the main water hose going into the washer which then released the part ,except from four wires. I then took one wire off at a time and attached to the new part one at a time.Finally, I was finished and reconnected everything .It worked perfected !I'am very happy and pleased . This washer is over 25 years old and still runs .

Removed old valve and replaced with new. Wire for wire..screw for screw..

I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.

I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)

took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

Removed three screws - Disconnected both inlet water hoses-Disconnected 4 electric clips-Removed internal hose connection from the same unit- Reverse order in assembly.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

Exactly as the video showed. This was a very simple repair. The only extra thing I did was to replace the mesh screen/gasket at the hose ends. They were plugged with crud. PartSelect saved me from buying a new washing machine. Yay!

My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.

Dennis Fleming
North Billerica, MA

pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.